Connerton CSP-2-18-3 18 In. Gas Stock Pot Range, Two 3-Ring Burners, 180,000 BTU, 44 In. Deep Body, Welded #304 Stainless

The Connerton CSP-2-18-3 is an 18 in. wide, 43-1/2 in. deep, 24 in. high gas stock pot range in the deep body, with two 3-ring, 90,000 BTU heavy duty painted cast iron burners set front and back for 180,000 BTU on a single 18 in. wide footprint, built for the ramen or pho house that runs a bone broth and a noodle water at the same time, the taqueria with beans and consomé going all day, or the banquet kitchen reducing two stocks side by side. Each burner section has its own pair of heavy duty brass valve knobs, so the front pot can roll at a hard boil while the back pot holds at a simmer. Through a Sunday brunch of pozole and a 60 qt pot of pasta water, the cast iron rings keep pushing heat into both pots and the grates carry the weight at a 24 in. working height. It is a two-pot floor unit with no oven, no griddle plate, and no side-by-side burner spacing, so it is for two large pots in line rather than a bank of sauté pans. It stands on the floor on 1-5/8 in. #304 stainless steel tubing legs over a stainless undershelf, connects at the rear through a 3/4 in. NPT inlet, ships with the gas pressure regulator that must be installed, and is for non-combustible locations only with 0 in. clearance at the sides and back.

Two 3-Ring 90,000 BTU Heavy Duty Painted Cast Iron Burners

The CSP-2-18-3 carries two burner sections in line, front and back, each a 3-ring heavy duty painted cast iron burner rated at 90,000 BTU, for 180,000 BTU on the deep body. Three concentric rings matter under a stock pot because the flame reaches the outer edge of a 16 in. pot bottom instead of concentrating in the center, so the whole pot comes up together and does not scorch in a ring in the middle. The mass of the cast iron rings also soaks up heat and keeps radiating it when you set a cold pot of water down, which is what gets a 40 qt batch to a boil faster. Both burners sit on an 18 in. wide, 43.5 in. deep body, so two pots stand one behind the other with the same width as a single-section stove.

Painted Cast Iron Grates With a Center-Slope Hole

Each grate is heavy duty painted cast iron with a center-slope hole. The surface pitches toward the opening over the burner, so a pot that boils over sends the spill down and through instead of leaving it to bake onto the grate top or run down the front panel. Cast iron has the mass to hold a full 60 qt pot steady while you stir with a paddle, and it takes the daily scrape of a bench scraper without complaint.

18 Gauge #304 Stainless Steel Body, Fully Welded

The body is 18 gauge #304 stainless steel, fully welded rather than screwed or riveted together. A welded seam has no gap for stock and grease to wick into and no fastener head to loosen after years of heat cycling, which is why Connerton lists it under easy cleaning and long life. #304 is the chromium-nickel grade that shrugs off acidic splatter from tomato broth and the wipe-down chemicals used on a line.

Removable 18 Gauge #304 Stainless Steel Front Panel and Drip Pan

The front panel is a removable 18 gauge #304 stainless steel piece, so a technician can open up the valve and burner area from the front without pulling the stove away from the wall or breaking the gas connection at the back. Under the burners sits an 18 gauge #304 stainless steel drip pan that collects what the center-slope grates send down and keeps boil-over off the floor.

Heavy Duty Brass Valves With a 3/4 In. NPT Rear Gas Inlet

The burners run on heavy duty brass valves, with 4 knobs on the front panel, two for each burner section. Brass valve bodies resist corrosion at the seat, which keeps a low simmer setting from drifting over months of stock work. Gas enters at the rear through a 3/4 in. NPT inlet. The unit runs on 4.0 in. W.C. natural gas or 11 in. W.C. propane, so specify the gas type when you order, and note the altitude if the kitchen sits above 2,000 ft so the orifices are sized correctly. The regulator is supplied in the carton and has to be installed.

1-5/8 In. #304 Stainless Steel Tubing Legs With Undershelf and Adjustable Feet

The stove stands 24 in. high on 1-5/8 in. round, 16 gauge #304 stainless steel tubing legs with adjustable feet, so you can level it on an uneven tile floor and keep a full pot from listing. A #304 stainless steel undershelf spans the legs beneath the burners, giving you a place for the lid, a spare pot, or a case of stock bones without adding a rack to the footprint. The leg tubing is the same #304 grade as the body, so it stands up to mop water and floor cleaners.

Stainless Steel Wok Adapter Ring Option

One factory option extends what the burners can do. A stainless steel wok adapter ring drops over a grate to cradle a round-bottom wok over the 3-ring flame, so the same 90,000 BTU that boils a stock pot can drive a high-heat stir fry when the pot comes off.