Skip to content

Everest EBNF2 39 In. Bottom Mount Reach-In Freezer, 2 Narrow Solid Doors, 33 Cu. Ft., Blizzard R290

SKUEBNF2 BrandEverest Refrigeration

The Everest Refrigeration EBNF2 Bottom Mount Reach-in Freezer

The Everest EBNF2 is the narrow two door freezer in Everest's EB Series bottom mount reach-in line, the answer when you want two-door access and 33 cubic feet of frozen storage but only have 39 3/8 inches of wall to give it. Two narrow solid stainless steel doors split the cabinet face so each opening vents only its own side, and with the condensing unit mounted below the cabinet the EBNF2 runs a deeper 33 1/8 inch body that swallows bulky frozen product and full-size baking sheet pans. Full stainless steel construction and pre-installed locks on both doors make it a working reach-in freezer for prep lines, bakeries and back-of-house frozen storage alike.

Bottom Mounted Blizzard R290 Cartridge that Swaps without On-Site Brazing

The condensing unit is a bottom mounted, self-contained Blizzard R290 cartridge that is fully detachable and replaceable in the field with no on-site brazing. Unlike a conventional sealed system repair that can park a freezer out of service while a refrigeration tech opens the circuit, a cartridge swap gets the box back to work the same visit. The 1 HP cartridge delivers 6,197 BTU per hour of cooling on natural R290 refrigerant with zero ozone depletion potential and a global warming potential of three, and an air circulation guard keeps the floor-level vents from being blocked by whatever gets pushed against the cabinet during a busy shift.

Electronically commutated fan motors pull the cabinet to temperature quickly while drawing less power, and the auto defrost cycle starts on a timer and ends on temperature, so it runs only as long as the coil needs. The condensate pan maintains itself with no external drain line or electric heater, which is one less floor penetration in your install. An auto-reverse condenser fan supports compressor ventilation and helps keep the condenser coil clean between cleanings, and pressure relief devices let staff re-open a just-closed door instead of waiting out the vacuum.

Two Narrow Solid Stainless Steel Doors with Self-Closing Torsion Hinges and Pre-Installed Locks

Each door is heavy duty stainless steel inside and out with the same 2.5 inch high density polyurethane insulation as the cabinet walls, and at 19 1/4 inches per opening the swings stay short, which matters in a galley aisle where a full-width door would block the walkway. Both doors self-close through adjustable torsion systems for a positive seal, carry high strength recessed handles that will not catch passing carts, and come with pre-installed locks so frozen stock stays put overnight. Frame heaters prevent exterior moisture build up on humid days, the snap-in magnetic gaskets pop out for cleaning or replacement without tools, and the doors are field reversible if your traffic flow runs the other way.

33 Cu. Ft. Deeper Cabinet Interior Built in Heavy Duty Stainless Steel

Inside there are no dividing walls, just one open 33 cubic foot compartment made deeper than Everest's top mount uprights so bulky boxed product and full-size baking sheet pans fit without diagonal stacking. Six epoxy coated steel wire shelves, three behind each door, ride height adjustable stainless steel clips, and the optional sheet pan mounting rack assembly adds bottom-support tray slides for standard full-size pans. The interior and exterior are heavy duty stainless steel with rounded corners that will not snag knuckles or towels, the top, bottom and rear are galvanized steel, and 2.5 inch high density polyurethane insulation fills the cabinet walls. A full-length air duct and airflow guard keep cold air moving through the whole cavity, and silicone coated, shatter-proof LED lighting gives bright, high color illumination with low heat output. The cabinet rolls on four 5 inch swivel casters with locks on the front set, and leg stabilizers come standard.

Digital Controller that Holds -10°F to 54°F with an Overheat Alarm

A multi-function digital controller with an easy to read LED display ships factory preset at -4°F and adjusts anywhere from -10°F to 54°F. An audible overheat alarm watches the compressor and condenser coil and sounds before a developing problem turns into lost product. Everest backs the unit with 3 year parts and labor, 5 year electrical, and 10 year compressor coverage, supported through its service agent network.

If the stock configuration does not match your line, Everest offers additional shelving, the sheet pan mounting rack assembly, a left hinged door, 3 inch locking swivel casters in place of the standard 5 inch set, and height adjustable interchangeable legs from 3.5 to 6 inches.

Keep in mind this is a freezer only; kitchens that also need chilled storage are better served by the refrigerator or dual temp cabinets in the same bottom mount line. The narrow format trades opening width for footprint: bulky bus tubs load easier through the wide single door sibling, and operations stocking for real volume should look at the full-width two and three door freezers in the family. It also runs taller than a top mount upright, standing 82 inches on its casters. Power is a standard 115V connection on a 9 foot cord, with no dedicated high-voltage circuit needed.

Features & Benefits

  1. Narrow two door bottom mount freezer for kitchens wanting split access in 39 3/8 in. of wall
  2. Stores 33 cu. ft. of frozen stock in a deeper 33 1/8 in. cabinet behind two narrow locking doors
  3. Keeps galley aisles clear with short 19 1/4 in. door swings on each side
  4. Swaps the entire bottom mounted Blizzard R290 cartridge in the field without on-site brazing
  5. Holds product anywhere from -10°F to 54°F on a digital controller preset at -4°F
  6. Fits standard full-size sheet pans with an optional bottom-support mounting rack assembly
  7. Keeps floor-level vents from obstruction with a built-in air circulation guard
  8. Defrosts on a time-initiated, temperature-terminated auto cycle with no operator input
  9. Cuts energy draw with ECM fan motors and a self-maintaining condensate pan
  10. Locks both doors with pre-installed locks to keep stock secure overnight
  11. Lights the cavity with silicone coated, shatter-proof LED at low heat output
  12. Adjusts six epoxy coated wire shelves on stainless steel height-adjustable clips
  13. Reverses both doors in the field to match your kitchen traffic flow
  14. Rolls on four 5 in. swivel casters with front locks and standard leg stabilizers
  15. Plugs in pre-wired and ready to run on a 9 ft cord, no electrician needed

Free Shipping ? 48 Contiguous states & DC only.

In Stock: Ships in 1-2 Business Days

$5,258.00
  • Narrow two door bottom mount freezer for kitchens wanting split access in 39 3/8 in. of wall
  • Stores 33 cu. ft. of frozen stock in a deeper 33 1/8 in. cabinet behind two narrow locking doors
  • Keeps galley aisles clear with short 19 1/4 in. door swings on each side
  • Swaps the entire bottom mounted Blizzard R290 cartridge in the field without on-site brazing
  • Holds product anywhere from -10°F to 54°F on a digital controller preset at -4°F
  • See full feature list

    The Everest Refrigeration EBNF2 Bottom Mount Reach-in Freezer

    The Everest EBNF2 is the narrow two door freezer in Everest's EB Series bottom mount reach-in line, the answer when you want two-door access and 33 cubic feet of frozen storage but only have 39 3/8 inches of wall to give it. Two narrow solid stainless steel doors split the cabinet face so each opening vents only its own side, and with the condensing unit mounted below the cabinet the EBNF2 runs a deeper 33 1/8 inch body that swallows bulky frozen product and full-size baking sheet pans. Full stainless steel construction and pre-installed locks on both doors make it a working reach-in freezer for prep lines, bakeries and back-of-house frozen storage alike.

    Bottom Mounted Blizzard R290 Cartridge that Swaps without On-Site Brazing

    The condensing unit is a bottom mounted, self-contained Blizzard R290 cartridge that is fully detachable and replaceable in the field with no on-site brazing. Unlike a conventional sealed system repair that can park a freezer out of service while a refrigeration tech opens the circuit, a cartridge swap gets the box back to work the same visit. The 1 HP cartridge delivers 6,197 BTU per hour of cooling on natural R290 refrigerant with zero ozone depletion potential and a global warming potential of three, and an air circulation guard keeps the floor-level vents from being blocked by whatever gets pushed against the cabinet during a busy shift.

    Electronically commutated fan motors pull the cabinet to temperature quickly while drawing less power, and the auto defrost cycle starts on a timer and ends on temperature, so it runs only as long as the coil needs. The condensate pan maintains itself with no external drain line or electric heater, which is one less floor penetration in your install. An auto-reverse condenser fan supports compressor ventilation and helps keep the condenser coil clean between cleanings, and pressure relief devices let staff re-open a just-closed door instead of waiting out the vacuum.

    Two Narrow Solid Stainless Steel Doors with Self-Closing Torsion Hinges and Pre-Installed Locks

    Each door is heavy duty stainless steel inside and out with the same 2.5 inch high density polyurethane insulation as the cabinet walls, and at 19 1/4 inches per opening the swings stay short, which matters in a galley aisle where a full-width door would block the walkway. Both doors self-close through adjustable torsion systems for a positive seal, carry high strength recessed handles that will not catch passing carts, and come with pre-installed locks so frozen stock stays put overnight. Frame heaters prevent exterior moisture build up on humid days, the snap-in magnetic gaskets pop out for cleaning or replacement without tools, and the doors are field reversible if your traffic flow runs the other way.

    33 Cu. Ft. Deeper Cabinet Interior Built in Heavy Duty Stainless Steel

    Inside there are no dividing walls, just one open 33 cubic foot compartment made deeper than Everest's top mount uprights so bulky boxed product and full-size baking sheet pans fit without diagonal stacking. Six epoxy coated steel wire shelves, three behind each door, ride height adjustable stainless steel clips, and the optional sheet pan mounting rack assembly adds bottom-support tray slides for standard full-size pans. The interior and exterior are heavy duty stainless steel with rounded corners that will not snag knuckles or towels, the top, bottom and rear are galvanized steel, and 2.5 inch high density polyurethane insulation fills the cabinet walls. A full-length air duct and airflow guard keep cold air moving through the whole cavity, and silicone coated, shatter-proof LED lighting gives bright, high color illumination with low heat output. The cabinet rolls on four 5 inch swivel casters with locks on the front set, and leg stabilizers come standard.

    Digital Controller that Holds -10°F to 54°F with an Overheat Alarm

    A multi-function digital controller with an easy to read LED display ships factory preset at -4°F and adjusts anywhere from -10°F to 54°F. An audible overheat alarm watches the compressor and condenser coil and sounds before a developing problem turns into lost product. Everest backs the unit with 3 year parts and labor, 5 year electrical, and 10 year compressor coverage, supported through its service agent network.

    If the stock configuration does not match your line, Everest offers additional shelving, the sheet pan mounting rack assembly, a left hinged door, 3 inch locking swivel casters in place of the standard 5 inch set, and height adjustable interchangeable legs from 3.5 to 6 inches.

    Keep in mind this is a freezer only; kitchens that also need chilled storage are better served by the refrigerator or dual temp cabinets in the same bottom mount line. The narrow format trades opening width for footprint: bulky bus tubs load easier through the wide single door sibling, and operations stocking for real volume should look at the full-width two and three door freezers in the family. It also runs taller than a top mount upright, standing 82 inches on its casters. Power is a standard 115V connection on a 9 foot cord, with no dedicated high-voltage circuit needed.

    Features & Benefits

    1. Narrow two door bottom mount freezer for kitchens wanting split access in 39 3/8 in. of wall
    2. Stores 33 cu. ft. of frozen stock in a deeper 33 1/8 in. cabinet behind two narrow locking doors
    3. Keeps galley aisles clear with short 19 1/4 in. door swings on each side
    4. Swaps the entire bottom mounted Blizzard R290 cartridge in the field without on-site brazing
    5. Holds product anywhere from -10°F to 54°F on a digital controller preset at -4°F
    6. Fits standard full-size sheet pans with an optional bottom-support mounting rack assembly
    7. Keeps floor-level vents from obstruction with a built-in air circulation guard
    8. Defrosts on a time-initiated, temperature-terminated auto cycle with no operator input
    9. Cuts energy draw with ECM fan motors and a self-maintaining condensate pan
    10. Locks both doors with pre-installed locks to keep stock secure overnight
    11. Lights the cavity with silicone coated, shatter-proof LED at low heat output
    12. Adjusts six epoxy coated wire shelves on stainless steel height-adjustable clips
    13. Reverses both doors in the field to match your kitchen traffic flow
    14. Rolls on four 5 in. swivel casters with front locks and standard leg stabilizers
    15. Plugs in pre-wired and ready to run on a 9 ft cord, no electrician needed

    Specifications

    Temp TypeFreezer
    Temperature Range-10°F to 54°F
    Factory Preset Temperature-4°F
    Net Capacity (Cu. Ft.)33
    Door Count2
    Door StyleSwing Solid, Narrow
    Door ConstructionStainless Steel Interior / Exterior, 2.5" Insulation
    Door HandlesHigh Strength Recessed
    Door LocksPre-Installed, Both Doors
    Door HingingField Reversible; Left Hinged Optional
    Door Width19 1/4" Each
    Door GasketsSnap-In Magnetic
    Frame HeatersStandard
    Shelves6 Epoxy Coated Steel Wire (3 Per Section)
    Shelf ClipsHeight Adjustable Stainless Steel
    Interior / Exterior FinishHeavy Duty Stainless Steel, Rounded Corners
    Top, Bottom and RearGalvanized Steel
    Insulation2.5" High Density Polyurethane
    LightingSilicone Coated, Shatter-Proof LED
    RefrigerantR-290
    Compressor HP1
    Compressor LocationBottom Mount
    BTU/Hr6,197
    Fan MotorsElectronically Commutated (ECM)
    Condenser and Evaporator CoilsLarge Capacity, Corrosion-Resistant
    Condenser FanHigh Performance, Auto-Reverse
    DefrostAuto, Time-Initiated and Temperature-Terminated
    Air Circulation GuardStandard, Keeps Floor Vents Clear
    Condensate ManagementSelf-Maintaining Drain Pan, No External Drain or Heater
    Pressure Relief DevicesStandard, For Rapid Cabinet Re-Entry
    Overheat AlarmAudible, Compressor and Condenser Coil
    Power (V-Hz-Ph)115-60-1
    Full Load Amps7.5
    NEMA Plug TypeNEMA 5-15P
    Cord Length9 Ft.
    Feed Wires3 With Ground
    CastersFour 5" Swivel, Locks on Front Set
    Leg StabilizersStandard
    Exterior Length39 3/8"
    Exterior Depth33 1/8"
    Depth With Door Open51 1/8"
    Exterior Height77"
    Overall Height (With 5" Casters)82"
    Crated Weight451 Lbs.
    Optional AccessoriesAdditional Shelving, Sheet Pan Mounting Rack Assembly (SMRA02-00), Left Hinged Door, 3" Caster Assembly (CASA3-01), 3.5"-6" Interchangeable Legs (AJL03-00)

    Manufacturer's Warranty

    • 10 Year

      Compressor

    • 3 Year

      Labor

    • 3 Year

      Parts

    • 5 Year

      Electrical

    Certifications & Approvals

    • NFS
      NSF Approved
    • CETLUS
      ETL US & Canada
    • ETLSAN
      ETL Sanitation

    The Chef Store is your go-to online destination for commercial food service equipment. We are committed to making your shopping experience seamless and ensuring you have the resources needed to make informed purchasing decisions. We continuously invest in product information development so that you have the knowledge and tools to choose the right equipment for your business. Whether you need help understanding product specifications or recommendations for your specific use case, our experienced team is here to help. We receive ongoing product training from the manufacturers we represent to ensure you are always well-informed and up to date. We pride ourselves on our core expertise: providing answers to your questions, guiding you through the decision-making process, and ultimately helping you make the best equipment purchasing decisions for your business.

    We're here to help. To us, that means no job is too big or too small. Whether you’re a national food chain or a small mom-and-pop shop, our commitment remains the same: ensuring every project is completed to your satisfaction. From the moment you place your order to delivery, we are dedicated to ensuring a seamless, hassle-free process. We continually evaluate and refine our operations, incorporating innovative technology to enhance efficiency and streamline communication with both customers and vendors. Our goal is to minimize delays and ensure your order reaches you as quickly and smoothly as possible.

    We carry a wide range of trusted restaurant equipment brands, and our catalog is always growing. If there's a particular item or brand you don't see on our website, please reach out to us; we’d be happy to help you find it. Not to mention, we leverage manufacturer and buying group relationships to offer our customers great prices and savings. Through these partnerships, freight programs, rebate programs, and more, we are able to purchase equipment at significant discounts and pass along the savings to our customers.

     

     

     

    We're excited to serve you next! 

    The Everest Refrigeration EBNF2 Bottom Mount Reach-in Freezer

    Product Features

    1. Narrow two door bottom mount freezer for kitchens wanting split access in 39 3/8 in. of wall
    2. Stores 33 cu. ft. of frozen stock in a deeper 33 1/8 in. cabinet behind two narrow locking doors
    3. Keeps galley aisles clear with short 19 1/4 in. door swings on each side
    4. Swaps the entire bottom mounted Blizzard R290 cartridge in the field without on-site brazing
    5. Holds product anywhere from -10°F to 54°F on a digital controller preset at -4°F
    6. Fits standard full-size sheet pans with an optional bottom-support mounting rack assembly
    7. Keeps floor-level vents from obstruction with a built-in air circulation guard
    8. Defrosts on a time-initiated, temperature-terminated auto cycle with no operator input
    9. Cuts energy draw with ECM fan motors and a self-maintaining condensate pan
    10. Locks both doors with pre-installed locks to keep stock secure overnight
    11. Lights the cavity with silicone coated, shatter-proof LED at low heat output
    12. Adjusts six epoxy coated wire shelves on stainless steel height-adjustable clips
    13. Reverses both doors in the field to match your kitchen traffic flow
    14. Rolls on four 5 in. swivel casters with front locks and standard leg stabilizers
    15. Plugs in pre-wired and ready to run on a 9 ft cord, no electrician needed

    Specifications

    Temp TypeFreezer
    Temperature Range-10°F to 54°F
    Factory Preset Temperature-4°F
    Net Capacity (Cu. Ft.)33
    Door Count2
    Door StyleSwing Solid, Narrow
    Door ConstructionStainless Steel Interior / Exterior, 2.5" Insulation
    Door HandlesHigh Strength Recessed
    Door LocksPre-Installed, Both Doors
    Door HingingField Reversible; Left Hinged Optional
    Door Width19 1/4" Each
    Door GasketsSnap-In Magnetic
    Frame HeatersStandard
    Shelves6 Epoxy Coated Steel Wire (3 Per Section)
    Shelf ClipsHeight Adjustable Stainless Steel
    Interior / Exterior FinishHeavy Duty Stainless Steel, Rounded Corners
    Top, Bottom and RearGalvanized Steel
    Insulation2.5" High Density Polyurethane
    LightingSilicone Coated, Shatter-Proof LED
    RefrigerantR-290
    Compressor HP1
    Compressor LocationBottom Mount
    BTU/Hr6,197
    Fan MotorsElectronically Commutated (ECM)
    Condenser and Evaporator CoilsLarge Capacity, Corrosion-Resistant
    Condenser FanHigh Performance, Auto-Reverse
    DefrostAuto, Time-Initiated and Temperature-Terminated
    Air Circulation GuardStandard, Keeps Floor Vents Clear
    Condensate ManagementSelf-Maintaining Drain Pan, No External Drain or Heater
    Pressure Relief DevicesStandard, For Rapid Cabinet Re-Entry
    Overheat AlarmAudible, Compressor and Condenser Coil
    Power (V-Hz-Ph)115-60-1
    Full Load Amps7.5
    NEMA Plug TypeNEMA 5-15P
    Cord Length9 Ft.
    Feed Wires3 With Ground
    CastersFour 5" Swivel, Locks on Front Set
    Leg StabilizersStandard
    Exterior Length39 3/8"
    Exterior Depth33 1/8"
    Depth With Door Open51 1/8"
    Exterior Height77"
    Overall Height (With 5" Casters)82"
    Crated Weight451 Lbs.
    Optional AccessoriesAdditional Shelving, Sheet Pan Mounting Rack Assembly (SMRA02-00), Left Hinged Door, 3" Caster Assembly (CASA3-01), 3.5"-6" Interchangeable Legs (AJL03-00)

    Manufacturer's Warranty

      10 year

      Compressor

      3 year

      Labor

      3 year

      Parts

      5 year

      Electrical

    Visit our help center
    Check your order status
    Return or exchange
    Get in touch