The Everest Refrigeration EGSH4 Reach-In Refrigerator
The Everest EGSH4 is the two section model in Everest's ES Series glass and solid combination half door lineup, built for kitchens that want a full display row of glass up top and protected bulk storage below across a 49 5/8 inch wide reach-in refrigerator. Two low emissivity double pane glass half doors let staff check stock across the entire upper level without opening anything, while two solid stainless steel half doors wrap the lower half of the 48 cubic foot interior in 2.5 inches of insulation, so every grab vents only a quarter of the cabinet face. At under 32 inches deep, the cabinet holds the same wall line as your worktables, and the full stainless steel body keeps it a working reach-in rather than a lightweight merchandiser.
Slide-Out Blizzard R290 Cartridge that Swaps without On-Site Brazing
The condensing unit is a top mounted, self-contained Blizzard R290 cartridge that is fully detachable and replaceable in the field with no on-site brazing. Unlike a conventional sealed system repair that can park a cabinet out of service while a refrigeration tech opens the circuit, a cartridge swap gets the box back to work the same visit. One 1/3 HP compressor rated at 2,311 BTU per hour carries the whole two section cavity on a modest 2.7 amp draw, and the cartridge runs natural R290 refrigerant with zero ozone depletion potential and a global warming potential of three.
Electronically commutated fan motors pull the cabinet to temperature quickly while drawing less power, and as a refrigerator the EGSH4 defrosts on an air cycle with no heater element involved. The condensate pan maintains itself with no external drain line or electric heater, which is one less floor penetration in your install. An auto-reverse condenser fan supports compressor ventilation and helps keep the condenser coil clean between cleanings, and pressure relief devices let staff re-open a just-closed door instead of waiting out the vacuum.
Two Low-E Glass Half Doors over Two Solid Stainless Steel Half Doors, All with Pre-Installed Locks
The upper doors pair low emissivity double glass panes with matte finish aluminum frames and heavy duty die-cast handles, so the shelves your staff hit all shift double as a stock-check window. The lower doors are built like the cabinet itself, heavy duty stainless steel inside and out with 2.5 inch high density polyurethane insulation and high strength recessed handles that will not catch carts in a tight aisle. All four doors self-close through adjustable torsion systems for a positive seal, frame heaters prevent exterior moisture build up on humid days, snap-in magnetic gaskets pop out for cleaning or replacement without tools, and pre-installed locks on every door keep stock secure overnight.
48 Cu. Ft. Open Interior Built in Heavy Duty Stainless Steel
Behind the split door face there are no dividing walls, just one open 48 cubic foot compartment with eight epoxy coated steel wire shelves on height adjustable stainless steel clips, so the half doors split the access, not the storage. The interior and exterior are heavy duty stainless steel with rounded corners that will not snag knuckles or towels, the top, bottom and rear are galvanized steel, and 2.5 inch high density polyurethane insulation fills the cabinet walls. A full-length air duct and airflow guard keep cold air moving through the whole cavity, and shielded LED bar lighting with its own on/off switch gives bright, high color illumination at low heat output, which earns its keep behind the glass upper doors. The cabinet rolls on four 5 inch swivel casters with locks on the front set.
Digital Controller that Holds 33°F to 54°F with an Overheat Alarm
A multi-function digital controller with an easy to read LED display ships factory preset at 35°F and adjusts anywhere from 33°F to 54°F. An audible overheat alarm watches the compressor and condenser coil and sounds before a developing problem turns into lost product. Everest backs the unit with 3 year parts and labor, 5 year electrical, and 10 year compressor coverage, supported through its service agent network.
If the stock configuration does not match your line, Everest offers additional shelving, a gravity shelf and bottle organizer, 3 inch locking swivel casters in place of the standard 5 inch set, and height adjustable interchangeable legs from 3.5 to 6 inches.
Keep in mind this is a refrigerator only, holding 33°F to 54°F, and the glass-over-solid split is fixed: if every shelf needs to read as a display, the all-glass half door cabinet on this footprint is the better fit, while kitchens that never show product get more insulation value from the all-solid version. Single station operations that do not need 48 cubic feet can hold the same combo format in the 29 1/4 inch single section sibling. Power is a standard 115V connection on a 9 foot cord, with no dedicated high-voltage circuit needed.
Features & Benefits
-
Two section combo reach-in for kitchens showing a glass display row over protected bulk storage
-
Stores 48 cu. ft. behind two glass and two solid half doors in a 49 5/8 in. footprint
-
Swaps the entire Blizzard R290 cooling cartridge in the field without on-site brazing
-
Holds product anywhere from 33°F to 54°F on a digital controller preset at 35°F
-
Shows upper-shelf stock through low emissivity double glass panes without opening a door
-
Insulates lower backstock behind solid stainless steel doors with 2.5 in. polyurethane fill
-
Locks all four doors with pre-installed locks to keep stock secure overnight
-
Runs the whole cavity on one 1/3 HP compressor drawing just 2.7 amps
-
Cuts energy draw with ECM fan motors and a self-maintaining condensate pan
-
Seals each swing with self-closing adjustable torsion systems and snap-in magnetic gaskets
-
Shows product under shielded LED bar lighting with its own on/off switch
-
Adjusts eight epoxy coated wire shelves on stainless steel height-adjustable clips
-
Prevents exterior moisture build up with standard door frame heaters
-
Rolls on four 5 in. swivel casters with locks on the front set
-
Plugs in pre-wired and ready to run on a 9 ft cord, no electrician needed
Free Shipping 48 Contiguous states & DC only.
In Stock: Ships in 1-2 Business Days
The Everest Refrigeration EGSH4 Reach-In Refrigerator
The Everest EGSH4 is the two section model in Everest's ES Series glass and solid combination half door lineup, built for kitchens that want a full display row of glass up top and protected bulk storage below across a 49 5/8 inch wide reach-in refrigerator. Two low emissivity double pane glass half doors let staff check stock across the entire upper level without opening anything, while two solid stainless steel half doors wrap the lower half of the 48 cubic foot interior in 2.5 inches of insulation, so every grab vents only a quarter of the cabinet face. At under 32 inches deep, the cabinet holds the same wall line as your worktables, and the full stainless steel body keeps it a working reach-in rather than a lightweight merchandiser.
Slide-Out Blizzard R290 Cartridge that Swaps without On-Site Brazing
The condensing unit is a top mounted, self-contained Blizzard R290 cartridge that is fully detachable and replaceable in the field with no on-site brazing. Unlike a conventional sealed system repair that can park a cabinet out of service while a refrigeration tech opens the circuit, a cartridge swap gets the box back to work the same visit. One 1/3 HP compressor rated at 2,311 BTU per hour carries the whole two section cavity on a modest 2.7 amp draw, and the cartridge runs natural R290 refrigerant with zero ozone depletion potential and a global warming potential of three.
Electronically commutated fan motors pull the cabinet to temperature quickly while drawing less power, and as a refrigerator the EGSH4 defrosts on an air cycle with no heater element involved. The condensate pan maintains itself with no external drain line or electric heater, which is one less floor penetration in your install. An auto-reverse condenser fan supports compressor ventilation and helps keep the condenser coil clean between cleanings, and pressure relief devices let staff re-open a just-closed door instead of waiting out the vacuum.
Two Low-E Glass Half Doors over Two Solid Stainless Steel Half Doors, All with Pre-Installed Locks
The upper doors pair low emissivity double glass panes with matte finish aluminum frames and heavy duty die-cast handles, so the shelves your staff hit all shift double as a stock-check window. The lower doors are built like the cabinet itself, heavy duty stainless steel inside and out with 2.5 inch high density polyurethane insulation and high strength recessed handles that will not catch carts in a tight aisle. All four doors self-close through adjustable torsion systems for a positive seal, frame heaters prevent exterior moisture build up on humid days, snap-in magnetic gaskets pop out for cleaning or replacement without tools, and pre-installed locks on every door keep stock secure overnight.
48 Cu. Ft. Open Interior Built in Heavy Duty Stainless Steel
Behind the split door face there are no dividing walls, just one open 48 cubic foot compartment with eight epoxy coated steel wire shelves on height adjustable stainless steel clips, so the half doors split the access, not the storage. The interior and exterior are heavy duty stainless steel with rounded corners that will not snag knuckles or towels, the top, bottom and rear are galvanized steel, and 2.5 inch high density polyurethane insulation fills the cabinet walls. A full-length air duct and airflow guard keep cold air moving through the whole cavity, and shielded LED bar lighting with its own on/off switch gives bright, high color illumination at low heat output, which earns its keep behind the glass upper doors. The cabinet rolls on four 5 inch swivel casters with locks on the front set.
Digital Controller that Holds 33°F to 54°F with an Overheat Alarm
A multi-function digital controller with an easy to read LED display ships factory preset at 35°F and adjusts anywhere from 33°F to 54°F. An audible overheat alarm watches the compressor and condenser coil and sounds before a developing problem turns into lost product. Everest backs the unit with 3 year parts and labor, 5 year electrical, and 10 year compressor coverage, supported through its service agent network.
If the stock configuration does not match your line, Everest offers additional shelving, a gravity shelf and bottle organizer, 3 inch locking swivel casters in place of the standard 5 inch set, and height adjustable interchangeable legs from 3.5 to 6 inches.
Keep in mind this is a refrigerator only, holding 33°F to 54°F, and the glass-over-solid split is fixed: if every shelf needs to read as a display, the all-glass half door cabinet on this footprint is the better fit, while kitchens that never show product get more insulation value from the all-solid version. Single station operations that do not need 48 cubic feet can hold the same combo format in the 29 1/4 inch single section sibling. Power is a standard 115V connection on a 9 foot cord, with no dedicated high-voltage circuit needed.
Features & Benefits
-
Two section combo reach-in for kitchens showing a glass display row over protected bulk storage
-
Stores 48 cu. ft. behind two glass and two solid half doors in a 49 5/8 in. footprint
-
Swaps the entire Blizzard R290 cooling cartridge in the field without on-site brazing
-
Holds product anywhere from 33°F to 54°F on a digital controller preset at 35°F
-
Shows upper-shelf stock through low emissivity double glass panes without opening a door
-
Insulates lower backstock behind solid stainless steel doors with 2.5 in. polyurethane fill
-
Locks all four doors with pre-installed locks to keep stock secure overnight
-
Runs the whole cavity on one 1/3 HP compressor drawing just 2.7 amps
-
Cuts energy draw with ECM fan motors and a self-maintaining condensate pan
-
Seals each swing with self-closing adjustable torsion systems and snap-in magnetic gaskets
-
Shows product under shielded LED bar lighting with its own on/off switch
-
Adjusts eight epoxy coated wire shelves on stainless steel height-adjustable clips
-
Prevents exterior moisture build up with standard door frame heaters
-
Rolls on four 5 in. swivel casters with locks on the front set
-
Plugs in pre-wired and ready to run on a 9 ft cord, no electrician needed
Resources & Downloads
Specifications
| Temp Type | Refrigerator |
| Temperature Range | 33°F to 54°F |
| Factory Preset Temperature | 35°F |
| Net Capacity (Cu. Ft.) | 48 |
| Door Count | 4 Half Doors (2 Glass, 2 Solid) |
| Door Style | Swing Solid & Glass Combo |
| Glass Type (Top Doors) | Low Emissivity Double Pane |
| Door Frame (Top Doors) | Matte Finish Aluminum |
| Solid Door Construction (Bottom Doors) | Stainless Steel Interior / Exterior, 2.5" Insulation |
| Door Handles | Die-Cast (Glass Doors), High Strength Recessed (Solid Doors) |
| Door Locks | Pre-Installed, All Doors |
| Door Width | 24" Each |
| Door Gaskets | Snap-In Magnetic |
| Frame Heaters | Standard |
| Shelves | 8 Epoxy Coated Steel Wire (4 Per Section) |
| Shelf Clips | Height Adjustable Stainless Steel |
| Interior / Exterior Finish | Heavy Duty Stainless Steel, Rounded Corners |
| Top, Bottom and Rear | Galvanized Steel |
| Insulation | 2.5" High Density Polyurethane |
| Lighting | Shielded LED Bar With On/Off Switch |
| Refrigerant | R-290 |
| Compressor HP | 1/3 |
| Compressor Location | Top Mount |
| BTU/Hr | 2,311 |
| Fan Motors | Electronically Commutated (ECM) |
| Condenser and Evaporator Coils | Large Capacity, Corrosion-Resistant |
| Condenser Fan | High Performance, Auto-Reverse |
| Defrost | Air Defrost |
| Condensate Management | Self-Maintaining Drain Pan, No External Drain or Heater |
| Pressure Relief Devices | Standard, For Rapid Cabinet Re-Entry |
| Overheat Alarm | Audible, Compressor and Condenser Coil |
| Power (V-Hz-Ph) | 115-60-1 |
| Full Load Amps | 2.7 |
| NEMA Plug Type | NEMA 5-15P |
| Cord Length | 9 Ft. |
| Feed Wires | 3 With Ground |
| Casters | Four 5" Swivel, Locks on Front Set |
| Exterior Length | 49 5/8" |
| Exterior Depth | 31 5/8" |
| Depth With Door Open | 54 1/2" |
| Exterior Height | 74 1/4" |
| Overall Height (With 5" Casters) | 79 1/4" |
| Crated Weight | 449 Lbs. |
| Optional Accessories | Additional Shelving, Gravity Shelf and Bottle Organizer (BO03), 3" Caster Assembly (CASA3-01), 3.5"-6" Interchangeable Legs (AJL03-00) |
Manufacturer's Warranty
-
10 Year
Compressor
-
3 Year
Labor
-
3 Year
Parts
-
5 Year
Electrical
Certifications & Approvals
-
ETL US & Canada
-
ETL Sanitation

