The Everest Refrigeration ESRF2D2 Reach In Dual Temperature
The Everest ESRF2D2 packs a drawered refrigerator station and a full size freezer into one 49 5/8 inch wide upright, the door and drawer dual temp in Everest's ES Series top mount reach-in family for kitchens that want chilled product at hand height and frozen backup without buying and plugging in two separate boxes. The left section keeps 22 cubic feet refrigerated behind a half door and two pull-out drawers, so the line grabs prep at station height all shift, while the right section's full door opens onto a 22 cubic foot freezer for the deep reserve. At under 32 inches deep it fits where two boxes never would.
Slide-Out Blizzard R290 Cartridge that Swaps without On-Site Brazing
Each zone runs its own top mounted, self-contained Blizzard R290 cartridge, fully detachable and replaceable in the field with no on-site brazing: a 1/4+ HP unit rated 1,926 BTU per hour on the refrigerator side and a 1/2 HP unit rated 1,670 BTU per hour on the freezer side. Unlike a conventional sealed system repair that can park a cabinet out of service while a refrigeration tech opens the circuit, a cartridge swap gets the box back to work the same visit, and a problem in one zone never takes down the other. Both cartridges run natural R290 refrigerant with zero ozone depletion potential and a global warming potential of three.
Electronically commutated fan motors pull both compartments to temperature quickly while drawing less power, and the auto defrost cycle starts on a timer and ends on temperature, so it runs only as long as the coils need. The condensate pan maintains itself with no external drain line or electric heater, which is one less floor penetration in your install. Auto-reverse condenser fans support compressor ventilation and help keep the coils clean between cleanings, and pressure relief devices let staff re-open a just-closed door instead of waiting out the vacuum.
One Solid Freezer Door Beside a Half Door over Two Refrigerated Ball-Bearing Drawers
Both doors are heavy duty stainless steel inside and out with the same 2.5 inch high density polyurethane insulation as the cabinet walls, so pulling chilled product never spills the freezer's air and vice versa. Each self-closes through an adjustable torsion system for a positive seal, carries a high strength recessed handle that will not catch passing carts, and comes with a pre-installed lock; the locks cover the doors only, not the drawers. The two refrigerated drawers ride in thick gauge stainless steel frames on low-friction ball bearings, so a loaded drawer rolls out with one hand instead of fighting the cook mid-rush. Snap-in magnetic gaskets on the doors and drawers pop out for cleaning or replacement without tools, and frame heaters prevent exterior moisture build up on humid days.
22 Cu. Ft. Refrigerator Beside a 22 Cu. Ft. Freezer Split by an Insulated Interior Wall
An insulated interior wall separates the two compartments, so the freezer holds deep frozen temperatures without dragging the refrigerator below its setpoint, unlike a single-cavity cabinet asked to do two jobs. Five epoxy coated steel wire shelves on height adjustable stainless steel clips split between the half door section and the freezer. The interior and exterior are heavy duty stainless steel with rounded corners that will not snag knuckles or towels, the top, bottom and rear are galvanized steel, and 2.5 inch high density polyurethane insulation fills the cabinet walls. A full-length air duct and airflow guard keep cold air moving through each compartment, and silicone coated, shatter-proof LED lighting gives bright, high color illumination with low heat output. The cabinet rolls on four 5 inch swivel casters with locks on the front set.
Independent Digital Controls that Hold 33°F to 54°F Chilled and -10°F to 54°F Frozen
Each compartment runs on its own multi-function digital control with an easy to read LED display, the refrigerator factory preset at 35°F and adjustable from 33°F to 54°F, the freezer preset at -4°F and adjustable from -10°F to 54°F. Dial one zone without touching the other as your menu shifts. An audible overheat alarm watches the compressors and condenser coils and sounds before a developing problem turns into lost product. Everest backs the unit with 3 year parts and labor, 5 year electrical, and 10 year compressor coverage, supported through its service agent network.
If the stock configuration does not match your line, Everest offers additional shelving, 3 inch locking swivel casters in place of the standard 5 inch set, and height adjustable interchangeable legs from 3.5 to 6 inches.
The dual temp drawer combo earns its keep where one cook pulls chilled product at the station while the freezer holds reserve; one footprint and one cord cover both jobs. If you want both zones on shelving instead of drawers, the two full door dual temp in the same series carries the same 22 plus 22 split, and an operation running everything at a single temperature gets more usable room from the straight two section refrigerator or freezer. Power is a standard 115V connection on a 9 foot cord, with no dedicated high-voltage circuit needed.
Features & Benefits
-
Dual temp combo for lines pulling chilled drawers at station height with frozen backup alongside
-
Splits 44 cu. ft. into a 22 cu. ft. refrigerator and a 22 cu. ft. freezer
-
Runs each zone on its own Blizzard R290 cartridge that swaps without on-site brazing
-
Holds 33°F to 54°F chilled and -10°F to 54°F frozen on independent digital controls
-
Slides loaded refrigerated drawers on thick gauge stainless frames with ball bearings
-
Keeps zones honest with an insulated interior wall between refrigerator and freezer
-
Cuts energy draw with ECM fan motors and low-heat, shatter-proof LED lighting
-
Defrosts on a time-initiated, temperature-terminated cycle with no operator input
-
Drains condensate into a self-maintaining pan with no external drain or electric heater
-
Seals both doors with self-closing adjustable torsion hinges for a positive seal
-
Cleans door and drawer gaskets fast with tool-free, snap-in magnetic design
-
Locks both doors overnight with pre-installed locks to keep shelved stock secure
-
Adjusts five epoxy coated wire shelves on stainless steel height-adjustable clips
-
Rolls on four 5 in. swivel casters with locks on the front set
-
Plugs in pre-wired and ready to run on a 9 ft cord, no electrician needed
Free Shipping 48 Contiguous states & DC only.
In Stock: Ships in 1-2 Business Days
The Everest Refrigeration ESRF2D2 Reach In Dual Temperature
The Everest ESRF2D2 packs a drawered refrigerator station and a full size freezer into one 49 5/8 inch wide upright, the door and drawer dual temp in Everest's ES Series top mount reach-in family for kitchens that want chilled product at hand height and frozen backup without buying and plugging in two separate boxes. The left section keeps 22 cubic feet refrigerated behind a half door and two pull-out drawers, so the line grabs prep at station height all shift, while the right section's full door opens onto a 22 cubic foot freezer for the deep reserve. At under 32 inches deep it fits where two boxes never would.
Slide-Out Blizzard R290 Cartridge that Swaps without On-Site Brazing
Each zone runs its own top mounted, self-contained Blizzard R290 cartridge, fully detachable and replaceable in the field with no on-site brazing: a 1/4+ HP unit rated 1,926 BTU per hour on the refrigerator side and a 1/2 HP unit rated 1,670 BTU per hour on the freezer side. Unlike a conventional sealed system repair that can park a cabinet out of service while a refrigeration tech opens the circuit, a cartridge swap gets the box back to work the same visit, and a problem in one zone never takes down the other. Both cartridges run natural R290 refrigerant with zero ozone depletion potential and a global warming potential of three.
Electronically commutated fan motors pull both compartments to temperature quickly while drawing less power, and the auto defrost cycle starts on a timer and ends on temperature, so it runs only as long as the coils need. The condensate pan maintains itself with no external drain line or electric heater, which is one less floor penetration in your install. Auto-reverse condenser fans support compressor ventilation and help keep the coils clean between cleanings, and pressure relief devices let staff re-open a just-closed door instead of waiting out the vacuum.
One Solid Freezer Door Beside a Half Door over Two Refrigerated Ball-Bearing Drawers
Both doors are heavy duty stainless steel inside and out with the same 2.5 inch high density polyurethane insulation as the cabinet walls, so pulling chilled product never spills the freezer's air and vice versa. Each self-closes through an adjustable torsion system for a positive seal, carries a high strength recessed handle that will not catch passing carts, and comes with a pre-installed lock; the locks cover the doors only, not the drawers. The two refrigerated drawers ride in thick gauge stainless steel frames on low-friction ball bearings, so a loaded drawer rolls out with one hand instead of fighting the cook mid-rush. Snap-in magnetic gaskets on the doors and drawers pop out for cleaning or replacement without tools, and frame heaters prevent exterior moisture build up on humid days.
22 Cu. Ft. Refrigerator Beside a 22 Cu. Ft. Freezer Split by an Insulated Interior Wall
An insulated interior wall separates the two compartments, so the freezer holds deep frozen temperatures without dragging the refrigerator below its setpoint, unlike a single-cavity cabinet asked to do two jobs. Five epoxy coated steel wire shelves on height adjustable stainless steel clips split between the half door section and the freezer. The interior and exterior are heavy duty stainless steel with rounded corners that will not snag knuckles or towels, the top, bottom and rear are galvanized steel, and 2.5 inch high density polyurethane insulation fills the cabinet walls. A full-length air duct and airflow guard keep cold air moving through each compartment, and silicone coated, shatter-proof LED lighting gives bright, high color illumination with low heat output. The cabinet rolls on four 5 inch swivel casters with locks on the front set.
Independent Digital Controls that Hold 33°F to 54°F Chilled and -10°F to 54°F Frozen
Each compartment runs on its own multi-function digital control with an easy to read LED display, the refrigerator factory preset at 35°F and adjustable from 33°F to 54°F, the freezer preset at -4°F and adjustable from -10°F to 54°F. Dial one zone without touching the other as your menu shifts. An audible overheat alarm watches the compressors and condenser coils and sounds before a developing problem turns into lost product. Everest backs the unit with 3 year parts and labor, 5 year electrical, and 10 year compressor coverage, supported through its service agent network.
If the stock configuration does not match your line, Everest offers additional shelving, 3 inch locking swivel casters in place of the standard 5 inch set, and height adjustable interchangeable legs from 3.5 to 6 inches.
The dual temp drawer combo earns its keep where one cook pulls chilled product at the station while the freezer holds reserve; one footprint and one cord cover both jobs. If you want both zones on shelving instead of drawers, the two full door dual temp in the same series carries the same 22 plus 22 split, and an operation running everything at a single temperature gets more usable room from the straight two section refrigerator or freezer. Power is a standard 115V connection on a 9 foot cord, with no dedicated high-voltage circuit needed.
Features & Benefits
-
Dual temp combo for lines pulling chilled drawers at station height with frozen backup alongside
-
Splits 44 cu. ft. into a 22 cu. ft. refrigerator and a 22 cu. ft. freezer
-
Runs each zone on its own Blizzard R290 cartridge that swaps without on-site brazing
-
Holds 33°F to 54°F chilled and -10°F to 54°F frozen on independent digital controls
-
Slides loaded refrigerated drawers on thick gauge stainless frames with ball bearings
-
Keeps zones honest with an insulated interior wall between refrigerator and freezer
-
Cuts energy draw with ECM fan motors and low-heat, shatter-proof LED lighting
-
Defrosts on a time-initiated, temperature-terminated cycle with no operator input
-
Drains condensate into a self-maintaining pan with no external drain or electric heater
-
Seals both doors with self-closing adjustable torsion hinges for a positive seal
-
Cleans door and drawer gaskets fast with tool-free, snap-in magnetic design
-
Locks both doors overnight with pre-installed locks to keep shelved stock secure
-
Adjusts five epoxy coated wire shelves on stainless steel height-adjustable clips
-
Rolls on four 5 in. swivel casters with locks on the front set
-
Plugs in pre-wired and ready to run on a 9 ft cord, no electrician needed
Resources & Downloads
Specifications
| Temp Type | Dual Temperature |
| Refrigerator Temperature Range | 33°F to 54°F (Preset 35°F) |
| Freezer Temperature Range | -10°F to 54°F (Preset -4°F) |
| Net Capacity (Cu. Ft.) | 22 (Refrigerator), 22 (Freezer) |
| Door Count | 1 Full Door, 1 Half Door, 2 Drawers |
| Door Style | Swing Solid + Drawer |
| Door Material | Stainless Steel Interior/Exterior |
| Door Width | 24" Each |
| Door Features | Self-Closing, Recessed Handles, Pre-Installed Locks (Doors Only) |
| Drawer Frames | Thick Gauge Stainless Steel, Low-Friction Ball Bearings |
| Door and Drawer Gaskets | Snap-In Magnetic |
| Frame Heaters | Standard |
| Shelves | 5 Epoxy Coated Steel Wire |
| Shelf Clips | Height Adjustable Stainless Steel |
| Interior / Exterior Finish | Heavy Duty Stainless Steel, Rounded Corners |
| Compartment Divider | Insulated Interior Wall |
| Top, Bottom and Rear | Galvanized Steel |
| Insulation | 2.5" High Density Polyurethane (Cabinet and Doors) |
| Lighting | Silicone Coated, Shatter-Proof LED |
| Refrigerant | R-290 |
| Compressor HP | 1/4+ (Refrigerator), 1/2 (Freezer) |
| Compressor Location | Top Mount |
| BTU/Hr | 1,926 (Refrigerator), 1,670 (Freezer) |
| Fan Motors | Electronically Commutated (ECM) |
| Condenser and Evaporator Coils | Large Capacity, Corrosion-Resistant |
| Condenser Fan | High Performance, Auto-Reverse |
| Defrost | Auto, Time-Initiated and Temperature-Terminated |
| Condensate Management | Self-Maintaining Drain Pan, No External Drain or Heater |
| Pressure Relief Devices | Standard, For Rapid Cabinet Re-Entry |
| Overheat Alarm | Audible, Compressor and Condenser Coil |
| Power (V-Hz-Ph) | 115-60-1 |
| Full Load Amps | 9.0 |
| NEMA Plug Type | NEMA 5-15P |
| Cord Length | 9 Ft. |
| Feed Wires | 3 With Ground |
| Casters | Four 5" Swivel, Locks on Front Set |
| Exterior Length | 49 5/8" |
| Exterior Depth | 31 5/8" |
| Depth With Doors Open | 54 1/2" |
| Exterior Height | 74 1/4" |
| Overall Height (With 5" Casters) | 79 1/4" |
| Crated Weight | 525 Lbs. |
| Optional Accessories | Additional Shelving, 3" Caster Assembly (CASA3-01), 3.5"-6" Interchangeable Legs (AJL03-00) |
Manufacturer's Warranty
-
10 Year
Compressor
-
3 Year
Labor
-
3 Year
Parts
-
5 Year
Electrical
Certifications & Approvals
-
NSF Approved
-
ETL US & Canada
-
ETL Sanitation

