Skip to content

Everest ESWQ2D2 59 In. Reach-In Dual Temp Refrigerator Freezer, Wide Door and 2 Drawers Chilled, Half Door Frozen, 39 + 13 Cu. Ft.

SKUESWQ2D2 BrandEverest Refrigeration

The Everest Refrigeration ESWQ2D2 Reach In Dual Temperature

The Everest ESWQ2D2 is the three-quarter chilled, one-quarter frozen member of Everest's ES Series door and drawer combo family, built for kitchens that live on refrigerated prep and only need a working stash of frozen product, not a whole freezer section. A wide 28 1/8 inch solid door on the left and two stainless steel drawers at station height on the right keep 39 cubic feet refrigerated, while the half door above the drawers closes off a 13 cubic foot freezer for the backup that one quarter of the box covers. All of it stands in one 59 inch wide upright on a single cord, under 32 inches deep so it holds the same wall line as your worktables.

Slide-Out Blizzard R290 Cartridge that Swaps without On-Site Brazing

Each zone runs its own top mounted, self-contained Blizzard R290 cartridge, fully detachable and replaceable in the field with no on-site brazing: a 1/4+ HP unit rated 1,926 BTU per hour on the refrigerator side and a 1/3 HP unit rated 2,311 BTU per hour on the freezer side. Unlike a conventional sealed system repair that can park a cabinet out of service while a refrigeration tech opens the circuit, a cartridge swap gets the box back to work the same visit, and a problem in one zone never takes down the other. Both cartridges run natural R290 refrigerant with zero ozone depletion potential and a global warming potential of three.

Electronically commutated fan motors pull both compartments to temperature quickly while drawing less power, and the auto defrost cycle starts on a timer and ends on temperature, so it runs only as long as the coils need. The condensate pan maintains itself with no external drain line or electric heater, which is one less floor penetration in your install. Auto-reverse condenser fans support compressor ventilation and help keep the coils clean between cleanings, and pressure relief devices let staff re-open a just-closed door instead of waiting out the vacuum.

One Wide Solid Refrigerator Door, a Half Door Freezer and Two Refrigerated Ball-Bearing Drawers

Both doors are heavy duty stainless steel inside and out with the same 2.5 inch high density polyurethane insulation as the cabinet walls, so pulling chilled product never spills the freezer's air and vice versa. Each self-closes through an adjustable torsion system for a positive seal, carries a high strength recessed handle that will not catch passing carts, and comes with a pre-installed lock; the locks cover the doors only, not the drawers. The two refrigerated drawers ride in thick gauge stainless steel frames on low-friction ball bearings, so a loaded drawer rolls out with one hand instead of fighting the cook mid-rush. Snap-in magnetic gaskets on the doors and drawers pop out for cleaning or replacement without tools, and frame heaters prevent exterior moisture build up on humid days.

39 Cu. Ft. Refrigerator and a 13 Cu. Ft. Freezer Quarter Split by an Insulated Interior Wall

An insulated interior wall closes the freezer quarter off from the refrigerated space, so the frozen zone holds deep temperatures without dragging the chilled side below its setpoint, unlike a single-cavity cabinet asked to do two jobs. Four epoxy coated steel wire shelves on height adjustable stainless steel clips split between the wide door section and the freezer. The interior and exterior are heavy duty stainless steel with rounded corners that will not snag knuckles or towels, the top, bottom and rear are galvanized steel, and 2.5 inch high density polyurethane insulation fills the cabinet walls. A full-length air duct and airflow guard keep cold air moving through each compartment, and silicone coated, shatter-proof LED lighting gives bright, high color illumination with low heat output. The cabinet rolls on four 5 inch swivel casters with locks on the front set.

Independent Digital Controls that Hold 33°F to 54°F Chilled and -10°F to 54°F Frozen

Each compartment runs on its own multi-function digital control with an easy to read LED display, the refrigerator factory preset at 35°F and adjustable from 33°F to 54°F, the freezer preset at -4°F and adjustable from -10°F to 54°F. Dial one zone without touching the other as your menu shifts. An audible overheat alarm watches the compressors and condenser coils and sounds before a developing problem turns into lost product. Everest backs the unit with 3 year parts and labor, 5 year electrical, and 10 year compressor coverage, supported through its service agent network.

If the stock configuration does not match your line, Everest offers additional shelving, 3 inch locking swivel casters in place of the standard 5 inch set, and height adjustable interchangeable legs from 3.5 to 6 inches.

The three-to-one split earns its keep where chilled prep dominates and frozen is a reserve; an operation pulling frozen product all day outgrows the 13 cubic foot quarter and is better matched by the even-split dual temp in the same series, while an all-chilled kitchen gets more usable room from a straight wide-door refrigerator. Power is a standard 115V connection on a 9 foot cord, with no dedicated high-voltage circuit needed.

Features & Benefits

  1. Three-quarter chilled dual temp for prep-heavy kitchens keeping a working frozen stash on the line
  2. Splits 52 cu. ft. into a 39 cu. ft. refrigerator and a 13 cu. ft. freezer
  3. Runs each zone on its own Blizzard R290 cartridge that swaps without on-site brazing
  4. Holds 33°F to 54°F chilled and -10°F to 54°F frozen on independent digital controls
  5. Slides loaded refrigerated drawers on thick gauge stainless frames with ball bearings
  6. Keeps zones honest with an insulated interior wall around the freezer quarter
  7. Loads bulky chilled stock through a wide 28 1/8 in. solid swing door
  8. Cuts energy draw with ECM fan motors and low-heat, shatter-proof LED lighting
  9. Defrosts on a time-initiated, temperature-terminated cycle with no operator input
  10. Drains condensate into a self-maintaining pan with no external drain or electric heater
  11. Cleans door and drawer gaskets fast with tool-free, snap-in magnetic design
  12. Locks both doors overnight with pre-installed locks to keep shelved stock secure
  13. Adjusts four epoxy coated wire shelves on stainless steel height-adjustable clips
  14. Rolls on four 5 in. swivel casters with locks on the front set
  15. Plugs in pre-wired and ready to run on a 9 ft cord, no electrician needed

Free Shipping ? 48 Contiguous states & DC only.

In Stock: Ships in 1-2 Business Days

$6,795.00
  • Three-quarter chilled dual temp for prep-heavy kitchens keeping a working frozen stash on the line
  • Splits 52 cu. ft. into a 39 cu. ft. refrigerator and a 13 cu. ft. freezer
  • Runs each zone on its own Blizzard R290 cartridge that swaps without on-site brazing
  • Holds 33°F to 54°F chilled and -10°F to 54°F frozen on independent digital controls
  • Slides loaded refrigerated drawers on thick gauge stainless frames with ball bearings
  • See full feature list

    The Everest Refrigeration ESWQ2D2 Reach In Dual Temperature

    The Everest ESWQ2D2 is the three-quarter chilled, one-quarter frozen member of Everest's ES Series door and drawer combo family, built for kitchens that live on refrigerated prep and only need a working stash of frozen product, not a whole freezer section. A wide 28 1/8 inch solid door on the left and two stainless steel drawers at station height on the right keep 39 cubic feet refrigerated, while the half door above the drawers closes off a 13 cubic foot freezer for the backup that one quarter of the box covers. All of it stands in one 59 inch wide upright on a single cord, under 32 inches deep so it holds the same wall line as your worktables.

    Slide-Out Blizzard R290 Cartridge that Swaps without On-Site Brazing

    Each zone runs its own top mounted, self-contained Blizzard R290 cartridge, fully detachable and replaceable in the field with no on-site brazing: a 1/4+ HP unit rated 1,926 BTU per hour on the refrigerator side and a 1/3 HP unit rated 2,311 BTU per hour on the freezer side. Unlike a conventional sealed system repair that can park a cabinet out of service while a refrigeration tech opens the circuit, a cartridge swap gets the box back to work the same visit, and a problem in one zone never takes down the other. Both cartridges run natural R290 refrigerant with zero ozone depletion potential and a global warming potential of three.

    Electronically commutated fan motors pull both compartments to temperature quickly while drawing less power, and the auto defrost cycle starts on a timer and ends on temperature, so it runs only as long as the coils need. The condensate pan maintains itself with no external drain line or electric heater, which is one less floor penetration in your install. Auto-reverse condenser fans support compressor ventilation and help keep the coils clean between cleanings, and pressure relief devices let staff re-open a just-closed door instead of waiting out the vacuum.

    One Wide Solid Refrigerator Door, a Half Door Freezer and Two Refrigerated Ball-Bearing Drawers

    Both doors are heavy duty stainless steel inside and out with the same 2.5 inch high density polyurethane insulation as the cabinet walls, so pulling chilled product never spills the freezer's air and vice versa. Each self-closes through an adjustable torsion system for a positive seal, carries a high strength recessed handle that will not catch passing carts, and comes with a pre-installed lock; the locks cover the doors only, not the drawers. The two refrigerated drawers ride in thick gauge stainless steel frames on low-friction ball bearings, so a loaded drawer rolls out with one hand instead of fighting the cook mid-rush. Snap-in magnetic gaskets on the doors and drawers pop out for cleaning or replacement without tools, and frame heaters prevent exterior moisture build up on humid days.

    39 Cu. Ft. Refrigerator and a 13 Cu. Ft. Freezer Quarter Split by an Insulated Interior Wall

    An insulated interior wall closes the freezer quarter off from the refrigerated space, so the frozen zone holds deep temperatures without dragging the chilled side below its setpoint, unlike a single-cavity cabinet asked to do two jobs. Four epoxy coated steel wire shelves on height adjustable stainless steel clips split between the wide door section and the freezer. The interior and exterior are heavy duty stainless steel with rounded corners that will not snag knuckles or towels, the top, bottom and rear are galvanized steel, and 2.5 inch high density polyurethane insulation fills the cabinet walls. A full-length air duct and airflow guard keep cold air moving through each compartment, and silicone coated, shatter-proof LED lighting gives bright, high color illumination with low heat output. The cabinet rolls on four 5 inch swivel casters with locks on the front set.

    Independent Digital Controls that Hold 33°F to 54°F Chilled and -10°F to 54°F Frozen

    Each compartment runs on its own multi-function digital control with an easy to read LED display, the refrigerator factory preset at 35°F and adjustable from 33°F to 54°F, the freezer preset at -4°F and adjustable from -10°F to 54°F. Dial one zone without touching the other as your menu shifts. An audible overheat alarm watches the compressors and condenser coils and sounds before a developing problem turns into lost product. Everest backs the unit with 3 year parts and labor, 5 year electrical, and 10 year compressor coverage, supported through its service agent network.

    If the stock configuration does not match your line, Everest offers additional shelving, 3 inch locking swivel casters in place of the standard 5 inch set, and height adjustable interchangeable legs from 3.5 to 6 inches.

    The three-to-one split earns its keep where chilled prep dominates and frozen is a reserve; an operation pulling frozen product all day outgrows the 13 cubic foot quarter and is better matched by the even-split dual temp in the same series, while an all-chilled kitchen gets more usable room from a straight wide-door refrigerator. Power is a standard 115V connection on a 9 foot cord, with no dedicated high-voltage circuit needed.

    Features & Benefits

    1. Three-quarter chilled dual temp for prep-heavy kitchens keeping a working frozen stash on the line
    2. Splits 52 cu. ft. into a 39 cu. ft. refrigerator and a 13 cu. ft. freezer
    3. Runs each zone on its own Blizzard R290 cartridge that swaps without on-site brazing
    4. Holds 33°F to 54°F chilled and -10°F to 54°F frozen on independent digital controls
    5. Slides loaded refrigerated drawers on thick gauge stainless frames with ball bearings
    6. Keeps zones honest with an insulated interior wall around the freezer quarter
    7. Loads bulky chilled stock through a wide 28 1/8 in. solid swing door
    8. Cuts energy draw with ECM fan motors and low-heat, shatter-proof LED lighting
    9. Defrosts on a time-initiated, temperature-terminated cycle with no operator input
    10. Drains condensate into a self-maintaining pan with no external drain or electric heater
    11. Cleans door and drawer gaskets fast with tool-free, snap-in magnetic design
    12. Locks both doors overnight with pre-installed locks to keep shelved stock secure
    13. Adjusts four epoxy coated wire shelves on stainless steel height-adjustable clips
    14. Rolls on four 5 in. swivel casters with locks on the front set
    15. Plugs in pre-wired and ready to run on a 9 ft cord, no electrician needed

    Specifications

    Temp TypeDual Temperature
    Refrigerator Temperature Range33°F to 54°F (Preset 35°F)
    Freezer Temperature Range-10°F to 54°F (Preset -4°F)
    Net Capacity (Cu. Ft.)39 (Refrigerator), 13 (Freezer)
    Door Count1 Full Door, 1 Half Door, 2 Drawers
    Door StyleSwing Solid + Drawer
    Door MaterialStainless Steel Interior/Exterior
    Door Width28 1/8" Each
    Door FeaturesSelf-Closing, Recessed Handles, Pre-Installed Locks (Doors Only)
    Drawer FramesThick Gauge Stainless Steel, Low-Friction Ball Bearings
    Door and Drawer GasketsSnap-In Magnetic
    Frame HeatersStandard
    Shelves4 Epoxy Coated Steel Wire
    Shelf ClipsHeight Adjustable Stainless Steel
    Interior / Exterior FinishHeavy Duty Stainless Steel, Rounded Corners
    Compartment DividerInsulated Interior Wall
    Top, Bottom and RearGalvanized Steel
    Insulation2.5" High Density Polyurethane (Cabinet and Doors)
    LightingSilicone Coated, Shatter-Proof LED
    RefrigerantR-290
    Compressor HP1/4+ (Refrigerator), 1/3 (Freezer)
    Compressor LocationTop Mount
    BTU/Hr1,926 (Refrigerator), 2,311 (Freezer)
    Fan MotorsElectronically Commutated (ECM)
    Condenser and Evaporator CoilsLarge Capacity, Corrosion-Resistant
    Condenser FanHigh Performance, Auto-Reverse
    DefrostAuto, Time-Initiated and Temperature-Terminated
    Condensate ManagementSelf-Maintaining Drain Pan, No External Drain or Heater
    Pressure Relief DevicesStandard, For Rapid Cabinet Re-Entry
    Overheat AlarmAudible, Compressor and Condenser Coil
    Power (V-Hz-Ph)115-60-1
    Full Load Amps5.5
    NEMA Plug TypeNEMA 5-15P
    Cord Length9 Ft.
    Feed Wires3 With Ground
    CastersFour 5" Swivel, Locks on Front Set
    Exterior Length59"
    Exterior Depth31 5/8"
    Depth With Doors Open58 5/8"
    Exterior Height74 1/4"
    Overall Height (With 5" Casters)79 1/4"
    Crated Weight556 Lbs.
    Optional AccessoriesAdditional Shelving, 3" Caster Assembly (CASA3-01), 3.5"-6" Interchangeable Legs (AJL03-00)

    Manufacturer's Warranty

    • 10 Year

      Compressor

    • 3 Year

      Labor

    • 3 Year

      Parts

    • 5 Year

      Electrical

    Certifications & Approvals

    • NFS
      NSF Approved
    • CETLUS
      ETL US & Canada
    • ETLSAN
      ETL Sanitation

    The Chef Store is your go-to online destination for commercial food service equipment. We are committed to making your shopping experience seamless and ensuring you have the resources needed to make informed purchasing decisions. We continuously invest in product information development so that you have the knowledge and tools to choose the right equipment for your business. Whether you need help understanding product specifications or recommendations for your specific use case, our experienced team is here to help. We receive ongoing product training from the manufacturers we represent to ensure you are always well-informed and up to date. We pride ourselves on our core expertise: providing answers to your questions, guiding you through the decision-making process, and ultimately helping you make the best equipment purchasing decisions for your business.

    We're here to help. To us, that means no job is too big or too small. Whether you’re a national food chain or a small mom-and-pop shop, our commitment remains the same: ensuring every project is completed to your satisfaction. From the moment you place your order to delivery, we are dedicated to ensuring a seamless, hassle-free process. We continually evaluate and refine our operations, incorporating innovative technology to enhance efficiency and streamline communication with both customers and vendors. Our goal is to minimize delays and ensure your order reaches you as quickly and smoothly as possible.

    We carry a wide range of trusted restaurant equipment brands, and our catalog is always growing. If there's a particular item or brand you don't see on our website, please reach out to us; we’d be happy to help you find it. Not to mention, we leverage manufacturer and buying group relationships to offer our customers great prices and savings. Through these partnerships, freight programs, rebate programs, and more, we are able to purchase equipment at significant discounts and pass along the savings to our customers.

     

     

     

    We're excited to serve you next! 

    The Everest Refrigeration ESWQ2D2 Reach In Dual Temperature

    Product Features

    1. Three-quarter chilled dual temp for prep-heavy kitchens keeping a working frozen stash on the line
    2. Splits 52 cu. ft. into a 39 cu. ft. refrigerator and a 13 cu. ft. freezer
    3. Runs each zone on its own Blizzard R290 cartridge that swaps without on-site brazing
    4. Holds 33°F to 54°F chilled and -10°F to 54°F frozen on independent digital controls
    5. Slides loaded refrigerated drawers on thick gauge stainless frames with ball bearings
    6. Keeps zones honest with an insulated interior wall around the freezer quarter
    7. Loads bulky chilled stock through a wide 28 1/8 in. solid swing door
    8. Cuts energy draw with ECM fan motors and low-heat, shatter-proof LED lighting
    9. Defrosts on a time-initiated, temperature-terminated cycle with no operator input
    10. Drains condensate into a self-maintaining pan with no external drain or electric heater
    11. Cleans door and drawer gaskets fast with tool-free, snap-in magnetic design
    12. Locks both doors overnight with pre-installed locks to keep shelved stock secure
    13. Adjusts four epoxy coated wire shelves on stainless steel height-adjustable clips
    14. Rolls on four 5 in. swivel casters with locks on the front set
    15. Plugs in pre-wired and ready to run on a 9 ft cord, no electrician needed

    Specifications

    Temp TypeDual Temperature
    Refrigerator Temperature Range33°F to 54°F (Preset 35°F)
    Freezer Temperature Range-10°F to 54°F (Preset -4°F)
    Net Capacity (Cu. Ft.)39 (Refrigerator), 13 (Freezer)
    Door Count1 Full Door, 1 Half Door, 2 Drawers
    Door StyleSwing Solid + Drawer
    Door MaterialStainless Steel Interior/Exterior
    Door Width28 1/8" Each
    Door FeaturesSelf-Closing, Recessed Handles, Pre-Installed Locks (Doors Only)
    Drawer FramesThick Gauge Stainless Steel, Low-Friction Ball Bearings
    Door and Drawer GasketsSnap-In Magnetic
    Frame HeatersStandard
    Shelves4 Epoxy Coated Steel Wire
    Shelf ClipsHeight Adjustable Stainless Steel
    Interior / Exterior FinishHeavy Duty Stainless Steel, Rounded Corners
    Compartment DividerInsulated Interior Wall
    Top, Bottom and RearGalvanized Steel
    Insulation2.5" High Density Polyurethane (Cabinet and Doors)
    LightingSilicone Coated, Shatter-Proof LED
    RefrigerantR-290
    Compressor HP1/4+ (Refrigerator), 1/3 (Freezer)
    Compressor LocationTop Mount
    BTU/Hr1,926 (Refrigerator), 2,311 (Freezer)
    Fan MotorsElectronically Commutated (ECM)
    Condenser and Evaporator CoilsLarge Capacity, Corrosion-Resistant
    Condenser FanHigh Performance, Auto-Reverse
    DefrostAuto, Time-Initiated and Temperature-Terminated
    Condensate ManagementSelf-Maintaining Drain Pan, No External Drain or Heater
    Pressure Relief DevicesStandard, For Rapid Cabinet Re-Entry
    Overheat AlarmAudible, Compressor and Condenser Coil
    Power (V-Hz-Ph)115-60-1
    Full Load Amps5.5
    NEMA Plug TypeNEMA 5-15P
    Cord Length9 Ft.
    Feed Wires3 With Ground
    CastersFour 5" Swivel, Locks on Front Set
    Exterior Length59"
    Exterior Depth31 5/8"
    Depth With Doors Open58 5/8"
    Exterior Height74 1/4"
    Overall Height (With 5" Casters)79 1/4"
    Crated Weight556 Lbs.
    Optional AccessoriesAdditional Shelving, 3" Caster Assembly (CASA3-01), 3.5"-6" Interchangeable Legs (AJL03-00)

    Manufacturer's Warranty

      10 year

      Compressor

      3 year

      Labor

      3 year

      Parts

      5 year

      Electrical

    Visit our help center
    Check your order status
    Return or exchange
    Get in touch