Skip to content

Everest ETF2-24 48 In. Side Mount Undercounter Freezer, 24 In. Depth Class, 2 Solid Doors, 9 Cu. Ft., Stainless Steel Worktop

SKUETF2-24 BrandEverest Refrigeration

The Everest Refrigeration ETF2-24 Undercounter Freezer

The Everest ETF2-24 is the shallow depth version of the two door ET Series side mount undercounter freezer, trimming the cabinet to 23 5/8 inches deep so 9 cubic feet of frozen storage and a 16 gauge stainless steel worktop fit where the standard 31 1/2 inch deep line will not. Narrow galleys, bar backs, and corridor prep lines get two independently locking 17 inch doors of frozen backup without surrendering walkway, and the top still works as prep counter space. The condensing unit rides in a housing at the left end and breathes through the front grille, so the cabinet backs flush against a wall or tucks under a shallow counter.

Side Mounted Blizzard R290 Cartridge that Swaps without On-Site Brazing

The cooling system is a side mounted, self-contained and fully detachable Blizzard R290 condensing unit, and because the whole cartridge slides out, a service tech can replace the entire sealed system without on-site brazing instead of parking the box for days over a compressor problem. The 1/2 horsepower compressor is rated at 1,979 BTU per hour and runs natural R290 refrigerant with zero ozone depletion potential and a global warming potential of three, and the unit arrives pre-wired and ready to plug in on a standard 115V circuit.

Electronically commutated fan motors pull the cabinet down to freezing while drawing less power, and a full-length air duct keeps cold air circulating evenly instead of pooling near the evaporator. Defrost runs automatically on a time-initiated, temperature-terminated cycle so the coil stays clear without anyone scraping it, the self-maintaining condensate pan needs no external drain line or electric heater, the auto-reverse condenser fan supports compressor ventilation and helps keep the condenser coil clean, and pressure relief devices let staff re-open a just-closed door instead of waiting out the vacuum a freezer pulls.

Two Solid Stainless Steel Doors with Pre-Installed Locks

Each 17 inch door opens its own side of the cabinet, so pulling fries from one end never spills cold air across the whole box, and in this shallow chassis the cabinet needs just 39 inches of clear depth with both doors open, the shortest swing in the side mount freezer line. The doors are heavy duty stainless steel inside and out with 2.5 inch high density polyurethane insulation, self-close through an adjustable torsion system, and carry snap-in magnetic gaskets that pop out for cleaning without tools. Frame heaters stop exterior moisture and frost build up around the openings, the high strength recessed handles stay out of the walkway, and the pre-installed locks keep stock secure after close.

9 Cu. Ft. Open Interior Under a 16 Gauge Stainless Steel Worktop

Behind the doors is an open spaced interior with no walls between compartments, so boxes and bins of frozen product slide in without fighting dividers. Four epoxy coated steel wire shelves, two per section, sit on height adjustable stainless steel clips, and silicone coated, shatter-proof LED lighting throws bright, high color light through the cavity while adding almost no heat. The interior and exterior are heavy duty stainless steel with rounded corners, the bottom and rear are galvanized steel, and 2.5 inch high density polyurethane insulation fills the cabinet walls. The body stands 29 1/4 inches tall, or 34 1/4 inches on its four 5 inch swivel casters with locks on the front set, so it rolls out for cleaning and locks in place during service.

Digital Controller that Holds -10°F to 54°F with an Overheat Alarm

A multi-function digital controller with an easy to read LED display ships preset at -4°F and adjusts anywhere from -10°F to 54°F, deep enough to hold ice cream hard while leaving room to run warmer when the menu changes. An audible overheat alarm watches the compressor and condenser coil and sounds before a developing problem turns into a thawed-out loss. Everest backs the unit with 3 year parts and labor, 5 year electrical, and 10 year compressor coverage, supported through its service agent network.

If the stock setup does not match your station, Everest offers additional shelving, a 4 inch high stainless steel backsplash (47 1/2 inches long) for worktop applications, a stainless steel double overshelf that adds two raised 45 by 13.5 inch shelves above the worktop, a 3 inch caster assembly in place of the standard 5 inch set, and height adjustable interchangeable legs from 3.5 to 6 inches.

Keep in mind the shallow chassis trades capacity for clearance: the full depth ETF2 carries 13 cubic feet in the same 47 1/2 inch length, so take the standard cabinet when the aisle allows it, and the single door ETF1-24 covers smaller stations in this same 24 inch depth class. The ETF2-24 is also a freezer first; chilled-only stations are better served by the ETR2-24 refrigerator in the same shallow footprint. On its standard casters the unit stands 34 1/4 inches overall, so verify your counter clearance and use the optional 3 inch casters or adjustable legs where the line runs lower. Power is a standard 115V connection drawing 5 amps on a 9 foot cord, with no dedicated circuit needed.

Features & Benefits

  1. Frozen point-of-use storage for narrow galleys, bar backs, and corridor prep lines
  2. Slides into shallow runs with a 23 5/8 in. deep cabinet, far less than full depth boxes
  3. Splits 9 cu. ft. of frozen stock behind two independently locking solid stainless steel doors
  4. Doubles as a tabletop workspace with a 16 gauge high quality stainless steel worktop
  5. Swaps the entire side mounted Blizzard R290 cartridge without on-site brazing
  6. Clears tight aisles, needing only 39 in. of depth with both doors open
  7. Tunes from -10°F to 54°F on a digital controller with an audible overheat alarm
  8. Backs flush against walls with a front breathing condensing unit at the left end
  9. Lights the cavity with silicone coated, shatter-proof LED strips with low heat output
  10. Cuts energy draw with ECM fan motors and a full-length cold air duct
  11. Defrosts automatically on a time-initiated, temperature-terminated cycle without interrupting service
  12. Drains condensate into a self-maintaining pan with no external drain or electric heater
  13. Fights frost at the openings with frame heaters around both doors
  14. Adjusts four epoxy coated wire shelves on height adjustable stainless steel clips

Free Shipping ? 48 Contiguous states & DC only.

In Stock: Ships in 1-2 Business Days

$3,614.00
  • Frozen point-of-use storage for narrow galleys, bar backs, and corridor prep lines
  • Slides into shallow runs with a 23 5/8 in. deep cabinet, far less than full depth boxes
  • Splits 9 cu. ft. of frozen stock behind two independently locking solid stainless steel doors
  • Doubles as a tabletop workspace with a 16 gauge high quality stainless steel worktop
  • Swaps the entire side mounted Blizzard R290 cartridge without on-site brazing
  • See full feature list

    The Everest Refrigeration ETF2-24 Undercounter Freezer

    The Everest ETF2-24 is the shallow depth version of the two door ET Series side mount undercounter freezer, trimming the cabinet to 23 5/8 inches deep so 9 cubic feet of frozen storage and a 16 gauge stainless steel worktop fit where the standard 31 1/2 inch deep line will not. Narrow galleys, bar backs, and corridor prep lines get two independently locking 17 inch doors of frozen backup without surrendering walkway, and the top still works as prep counter space. The condensing unit rides in a housing at the left end and breathes through the front grille, so the cabinet backs flush against a wall or tucks under a shallow counter.

    Side Mounted Blizzard R290 Cartridge that Swaps without On-Site Brazing

    The cooling system is a side mounted, self-contained and fully detachable Blizzard R290 condensing unit, and because the whole cartridge slides out, a service tech can replace the entire sealed system without on-site brazing instead of parking the box for days over a compressor problem. The 1/2 horsepower compressor is rated at 1,979 BTU per hour and runs natural R290 refrigerant with zero ozone depletion potential and a global warming potential of three, and the unit arrives pre-wired and ready to plug in on a standard 115V circuit.

    Electronically commutated fan motors pull the cabinet down to freezing while drawing less power, and a full-length air duct keeps cold air circulating evenly instead of pooling near the evaporator. Defrost runs automatically on a time-initiated, temperature-terminated cycle so the coil stays clear without anyone scraping it, the self-maintaining condensate pan needs no external drain line or electric heater, the auto-reverse condenser fan supports compressor ventilation and helps keep the condenser coil clean, and pressure relief devices let staff re-open a just-closed door instead of waiting out the vacuum a freezer pulls.

    Two Solid Stainless Steel Doors with Pre-Installed Locks

    Each 17 inch door opens its own side of the cabinet, so pulling fries from one end never spills cold air across the whole box, and in this shallow chassis the cabinet needs just 39 inches of clear depth with both doors open, the shortest swing in the side mount freezer line. The doors are heavy duty stainless steel inside and out with 2.5 inch high density polyurethane insulation, self-close through an adjustable torsion system, and carry snap-in magnetic gaskets that pop out for cleaning without tools. Frame heaters stop exterior moisture and frost build up around the openings, the high strength recessed handles stay out of the walkway, and the pre-installed locks keep stock secure after close.

    9 Cu. Ft. Open Interior Under a 16 Gauge Stainless Steel Worktop

    Behind the doors is an open spaced interior with no walls between compartments, so boxes and bins of frozen product slide in without fighting dividers. Four epoxy coated steel wire shelves, two per section, sit on height adjustable stainless steel clips, and silicone coated, shatter-proof LED lighting throws bright, high color light through the cavity while adding almost no heat. The interior and exterior are heavy duty stainless steel with rounded corners, the bottom and rear are galvanized steel, and 2.5 inch high density polyurethane insulation fills the cabinet walls. The body stands 29 1/4 inches tall, or 34 1/4 inches on its four 5 inch swivel casters with locks on the front set, so it rolls out for cleaning and locks in place during service.

    Digital Controller that Holds -10°F to 54°F with an Overheat Alarm

    A multi-function digital controller with an easy to read LED display ships preset at -4°F and adjusts anywhere from -10°F to 54°F, deep enough to hold ice cream hard while leaving room to run warmer when the menu changes. An audible overheat alarm watches the compressor and condenser coil and sounds before a developing problem turns into a thawed-out loss. Everest backs the unit with 3 year parts and labor, 5 year electrical, and 10 year compressor coverage, supported through its service agent network.

    If the stock setup does not match your station, Everest offers additional shelving, a 4 inch high stainless steel backsplash (47 1/2 inches long) for worktop applications, a stainless steel double overshelf that adds two raised 45 by 13.5 inch shelves above the worktop, a 3 inch caster assembly in place of the standard 5 inch set, and height adjustable interchangeable legs from 3.5 to 6 inches.

    Keep in mind the shallow chassis trades capacity for clearance: the full depth ETF2 carries 13 cubic feet in the same 47 1/2 inch length, so take the standard cabinet when the aisle allows it, and the single door ETF1-24 covers smaller stations in this same 24 inch depth class. The ETF2-24 is also a freezer first; chilled-only stations are better served by the ETR2-24 refrigerator in the same shallow footprint. On its standard casters the unit stands 34 1/4 inches overall, so verify your counter clearance and use the optional 3 inch casters or adjustable legs where the line runs lower. Power is a standard 115V connection drawing 5 amps on a 9 foot cord, with no dedicated circuit needed.

    Features & Benefits

    1. Frozen point-of-use storage for narrow galleys, bar backs, and corridor prep lines
    2. Slides into shallow runs with a 23 5/8 in. deep cabinet, far less than full depth boxes
    3. Splits 9 cu. ft. of frozen stock behind two independently locking solid stainless steel doors
    4. Doubles as a tabletop workspace with a 16 gauge high quality stainless steel worktop
    5. Swaps the entire side mounted Blizzard R290 cartridge without on-site brazing
    6. Clears tight aisles, needing only 39 in. of depth with both doors open
    7. Tunes from -10°F to 54°F on a digital controller with an audible overheat alarm
    8. Backs flush against walls with a front breathing condensing unit at the left end
    9. Lights the cavity with silicone coated, shatter-proof LED strips with low heat output
    10. Cuts energy draw with ECM fan motors and a full-length cold air duct
    11. Defrosts automatically on a time-initiated, temperature-terminated cycle without interrupting service
    12. Drains condensate into a self-maintaining pan with no external drain or electric heater
    13. Fights frost at the openings with frame heaters around both doors
    14. Adjusts four epoxy coated wire shelves on height adjustable stainless steel clips

    Specifications

    Temp TypeFreezer
    Temperature Range-10°F to 54°F
    Factory Preset-4°F
    Cu. Ft. Capacity9
    Interior LayoutOpen Spaced, No Walls Between Compartments
    Door Count2
    Door StyleSwing Solid
    Door Width17" Each
    Door FeaturesSelf-Closing, Recessed Handles, Pre-Installed Locks
    Door GasketsSnap-In Magnetic
    Frame HeatersStandard
    Shelves4 Epoxy Coated Steel Wire (2 Per Section)
    Shelf ClipsHeight Adjustable Stainless Steel
    LightingSilicone Coated, Shatter-Proof LED
    Worktop16 Gauge Stainless Steel
    Interior / Exterior FinishHeavy Duty Stainless Steel, Rounded Corners
    Bottom and RearGalvanized Steel
    Insulation2.5" High Density Polyurethane (Cabinet and Doors)
    RefrigerantR-290
    Compressor HP1/2
    Compressor LocationSide Mount
    BTU/Hr1,979
    Fan MotorsElectronically Commutated (ECM)
    Air CirculationFull-Length Air Duct
    Condenser and Evaporator CoilsLarge Capacity, Corrosion-Resistant
    Condenser FanHigh Performance, Auto-Reverse
    DefrostAuto, Time-Initiated and Temperature-Terminated
    Condensate ManagementSelf-Maintaining Drain Pan, No External Drain or Heater
    Pressure Relief DevicesStandard, For Rapid Cabinet Re-Entry
    Overheat AlarmAudible, Compressor and Condenser Coil
    Power (V-Hz-Ph)115-60-1
    Full Load Amps5
    NEMA Plug TypeNEMA 5-15P
    Cord Length9 Ft.
    Feed Wires3 With Ground
    CastersFour 5" Swivel, Locks on Front Set
    Exterior Length47 1/2"
    Exterior Depth23 5/8"
    Depth With Doors Open39"
    Exterior Height29 1/4"
    Overall Height (With 5" Casters)34 1/4"
    Crated Weight184 Lbs.
    Optional AccessoriesAdditional Shelving, 4" Stainless Steel Backsplash (BKSPL02-00), Double Overshelf (OS26-00), 3" Caster Assembly (CASA3-01), 3.5"-6" Interchangeable Legs (AJL03-00)

    Manufacturer's Warranty

    • 10 Year

      Compressor

    • 3 Year

      Labor

    • 3 Year

      Parts

    • 5 Year

      Electrical

    Certifications & Approvals

    • CETLUS
      ETL US & Canada
    • ETLSAN
      ETL Sanitation

    The Chef Store is your go-to online destination for commercial food service equipment. We are committed to making your shopping experience seamless and ensuring you have the resources needed to make informed purchasing decisions. We continuously invest in product information development so that you have the knowledge and tools to choose the right equipment for your business. Whether you need help understanding product specifications or recommendations for your specific use case, our experienced team is here to help. We receive ongoing product training from the manufacturers we represent to ensure you are always well-informed and up to date. We pride ourselves on our core expertise: providing answers to your questions, guiding you through the decision-making process, and ultimately helping you make the best equipment purchasing decisions for your business.

    We're here to help. To us, that means no job is too big or too small. Whether you’re a national food chain or a small mom-and-pop shop, our commitment remains the same: ensuring every project is completed to your satisfaction. From the moment you place your order to delivery, we are dedicated to ensuring a seamless, hassle-free process. We continually evaluate and refine our operations, incorporating innovative technology to enhance efficiency and streamline communication with both customers and vendors. Our goal is to minimize delays and ensure your order reaches you as quickly and smoothly as possible.

    We carry a wide range of trusted restaurant equipment brands, and our catalog is always growing. If there's a particular item or brand you don't see on our website, please reach out to us; we’d be happy to help you find it. Not to mention, we leverage manufacturer and buying group relationships to offer our customers great prices and savings. Through these partnerships, freight programs, rebate programs, and more, we are able to purchase equipment at significant discounts and pass along the savings to our customers.

     

     

     

    We're excited to serve you next! 

    The Everest Refrigeration ETF2-24 Undercounter Freezer

    About Undercounter Freezers

    Undercounter freezers give you frozen storage where you need it. They fit under counters and prep tables. Restaurants, bars, delis, and food trucks use them to keep frozen product close without losing floor space. They hold temp, even in busy, hot kitchens.

    Most undercounter freezers have solid doors. Drawer models are common on cook lines where staff need quick access without bending down. Drawers speed up service and keep staff at their station. Both types fit under standard counters and come in different widths.

    Pick your freezer based on size, capacity, and how it fits your line. Small units work for tight spots or as backup storage. Larger ones hold more if you need volume at the station. Measure your space and match the unit to what you actually use each day.

    Common Types and Configurations

    • Standard Door Undercounter Freezer: Solid door. Fits under standard counters. Single or double door. Reliable frozen storage in a small footprint.
    • Commercial Undercounter Freezer with Drawers: Pull-out drawers instead of doors. Faster access on the line. Good for stations where staff need to grab product fast.
    • Small Commercial Undercounter Freezer: Compact. Fits tight spaces or works as extra storage. Same performance as bigger models.
    • Worktop Undercounter Freezer: Has a stainless prep top. Gives you frozen storage and a work surface in one unit.
    • Commercial Grade Freezer: Built for daily use. Heavy-duty compressor, tough gaskets, and interiors made for busy kitchens.

    What to Look at Before You Buy

    • Unit Dimensions: Measure your space before you buy. Most fit under 36 inch counters, but check height, width, and depth against your setup.
    • Door vs. Drawer: Doors cost less and give full access. Drawers cost more but speed up workflow on busy lines.
    • Temperature Range: Make sure the unit holds 0°F or below, even when loaded. If your kitchen is hot, check the ambient temp rating on the spec sheet.
    • Capacity: Size the unit for what you actually need to store at the station. If one undercounter freezer is not enough, look at a reach-in or add a second unit.
    • Compressor Location: Most units have the compressor on the left or right. Make sure there is enough space for airflow and no conflict with other equipment.
    • Defrost System: Most use automatic defrost. Make sure the cycle fits your usage and does not cause temp spikes that hurt product quality.

    Frequently Asked Questions

    What is a commercial undercounter freezer?

    An undercounter freezer is a compact freezer that fits under your counter or prep table. It keeps frozen product at the station for fast access. You see them in restaurants, bars, delis, and food trucks where space is tight and you need frozen storage close by.

    What is the difference between a commercial undercounter freezer and a worktop freezer?

    The difference is the top. A worktop freezer has a stainless prep surface. An undercounter freezer slides under your existing counter. Both give you frozen storage, but a worktop is freestanding and has its own top. An undercounter unit fits into your counter run.

    What sizes do commercial undercounter freezers come in?

    Undercounter freezers come in widths from 27 to 60 inches. Most fit under 36 inch counters and are about 30 inches deep. Width is the main thing to check. Measure your counter run and make sure the unit fits before you order.

    Related Categories

    Shop by Brand

    Product Features

    1. Frozen point-of-use storage for narrow galleys, bar backs, and corridor prep lines
    2. Slides into shallow runs with a 23 5/8 in. deep cabinet, far less than full depth boxes
    3. Splits 9 cu. ft. of frozen stock behind two independently locking solid stainless steel doors
    4. Doubles as a tabletop workspace with a 16 gauge high quality stainless steel worktop
    5. Swaps the entire side mounted Blizzard R290 cartridge without on-site brazing
    6. Clears tight aisles, needing only 39 in. of depth with both doors open
    7. Tunes from -10°F to 54°F on a digital controller with an audible overheat alarm
    8. Backs flush against walls with a front breathing condensing unit at the left end
    9. Lights the cavity with silicone coated, shatter-proof LED strips with low heat output
    10. Cuts energy draw with ECM fan motors and a full-length cold air duct
    11. Defrosts automatically on a time-initiated, temperature-terminated cycle without interrupting service
    12. Drains condensate into a self-maintaining pan with no external drain or electric heater
    13. Fights frost at the openings with frame heaters around both doors
    14. Adjusts four epoxy coated wire shelves on height adjustable stainless steel clips

    Specifications

    Temp TypeFreezer
    Temperature Range-10°F to 54°F
    Factory Preset-4°F
    Cu. Ft. Capacity9
    Interior LayoutOpen Spaced, No Walls Between Compartments
    Door Count2
    Door StyleSwing Solid
    Door Width17" Each
    Door FeaturesSelf-Closing, Recessed Handles, Pre-Installed Locks
    Door GasketsSnap-In Magnetic
    Frame HeatersStandard
    Shelves4 Epoxy Coated Steel Wire (2 Per Section)
    Shelf ClipsHeight Adjustable Stainless Steel
    LightingSilicone Coated, Shatter-Proof LED
    Worktop16 Gauge Stainless Steel
    Interior / Exterior FinishHeavy Duty Stainless Steel, Rounded Corners
    Bottom and RearGalvanized Steel
    Insulation2.5" High Density Polyurethane (Cabinet and Doors)
    RefrigerantR-290
    Compressor HP1/2
    Compressor LocationSide Mount
    BTU/Hr1,979
    Fan MotorsElectronically Commutated (ECM)
    Air CirculationFull-Length Air Duct
    Condenser and Evaporator CoilsLarge Capacity, Corrosion-Resistant
    Condenser FanHigh Performance, Auto-Reverse
    DefrostAuto, Time-Initiated and Temperature-Terminated
    Condensate ManagementSelf-Maintaining Drain Pan, No External Drain or Heater
    Pressure Relief DevicesStandard, For Rapid Cabinet Re-Entry
    Overheat AlarmAudible, Compressor and Condenser Coil
    Power (V-Hz-Ph)115-60-1
    Full Load Amps5
    NEMA Plug TypeNEMA 5-15P
    Cord Length9 Ft.
    Feed Wires3 With Ground
    CastersFour 5" Swivel, Locks on Front Set
    Exterior Length47 1/2"
    Exterior Depth23 5/8"
    Depth With Doors Open39"
    Exterior Height29 1/4"
    Overall Height (With 5" Casters)34 1/4"
    Crated Weight184 Lbs.
    Optional AccessoriesAdditional Shelving, 4" Stainless Steel Backsplash (BKSPL02-00), Double Overshelf (OS26-00), 3" Caster Assembly (CASA3-01), 3.5"-6" Interchangeable Legs (AJL03-00)

    Manufacturer's Warranty

      10 year

      Compressor

      3 year

      Labor

      3 year

      Parts

      5 year

      Electrical

    Visit our help center
    Check your order status
    Return or exchange
    Get in touch