The Omcan 24407 Work Table
This Omcan cabinet base work table gives you a 60 inch stainless steel work surface with an enclosed cabinet underneath for storing kitchen equipment and other products. It is intended for food preparation in a busy commercial kitchen. Sliding doors close off the base, so what you keep under the work top stays behind doors. The top is 18-gauge type 304 stainless steel, and this is the overhang edge version, with the top larger than the cabinet body beneath it. A 4 inch by 1 inch backsplash runs along the back edge. The unit stands 38 inches high at the top of the backsplash on a 30 inch deep footprint, so measure your wall run and aisle clearance against the 60 inch width. The top is rated for 750 pounds and the undershelf inside the cabinet for 440 pounds. It arrives as a knock-down unit that assembles on site with set screws.
Enclosed Cabinet Base with Sliding Doors
The base is an enclosed cabinet closed in by a back panel and left and right side panels, with a stainless steel undershelf inside and two sliding doors across the front. The doors ride on slide rails and have recessed handles. The cabinet body measures 53-1/2 inches wide by 21-3/4 inches deep, and its bottom sits 12 inches off the floor.
18-Gauge Type 304 Stainless Steel Construction
Omcan builds this table in 18-gauge type 304 stainless steel. The top, the legs and the undershelf are all stainless steel, and the table is designed and finished for commercial use, so minor surface marks such as dimples, scratches and scuffs are normal on a product of this kind. The same table is available in type 430 stainless steel as item 24404.
4-Inch by 1-Inch Backsplash and Overhang Edge
The back edge carries a 4 inch by 1 inch backsplash. The work surface sits 34 inches off the floor and the top of the splash at 38 inches, worth checking if the table slides under a wall shelf. The rest of the top is the overhang edge: The top extends 3-1/4 inches beyond the cabinet body at each end and 4-1/8 inches at the front and back. The same table is available without a backsplash as item 24401.
Knock-Down Design Assembled on Site
The table arrives knocked down with four 34 inch stainless steel legs, the top, two sides, a back, the undershelf with its aluminum die cast clamp, two sliding doors and 36 set screws. The back and sides fasten to the top with set screws, the legs and undershelf assembly insert into gussets, and the doors are installed on the slide rails once the table is upright. The set screws should be filled with an approved silicone sealer, which is not included. The legs finish in stainless steel bullet feet. Optional 5 inch casters are items 47599 (without brake) and 14395 (with brake).
About Omcan
For over 74 years, Omcan has been a trusted name in the foodservice industry across Canada and the United States. Built on consistency, credibility, and long-standing customer relationships, Omcan offers a dependable range of products to support a wide range of operations. With a global network and localized service, the brand delivers complete solutions—from smallwares to advanced equipment. In 2024, Omcan introduced the Trento brand, representing a curated lineup of European foodservice equipment available exclusively in North America. Whether supporting independent operators or institutional kitchens, Omcan is focused on practical performance and reliable service.
Features & Benefits
-
Enclosed cabinet work table for food preparation in a busy commercial kitchen, with a 60 inch by 30 inch top
-
Cabinet is closed in by back and side panels with a stainless steel undershelf inside for storing kitchen equipment and other products
-
Two sliding doors on slide rails with recessed handles across the front of the cabinet
-
18 gauge type 304 stainless steel construction, with a stainless steel top, legs and undershelf
-
Overhang edge top that extends past the cabinet body at the ends, front and back
-
4 inch by 1 inch backsplash along the back of the top; the same table without a backsplash is item 24401
-
Top rated for a heavier load than the undershelf inside the cabinet
-
Four 34 inch stainless steel legs with stainless steel bullet feet; optional 5 inch casters available as items 47599 and 14395
-
Knock-down design that assembles on site with 36 set screws, which should be filled with an approved silicone sealer (not included)
Free Shipping 48 Contiguous states & DC only.
In Stock: Ships in 1-2 Business Days
Enclosed cabinet work table for food preparation in a busy commercial kitchen, with a 60 inch by 30 inch top
Cabinet is closed in by back and side panels with a stainless steel undershelf inside for storing kitchen equipment and other products
Two sliding doors on slide rails with recessed handles across the front of the cabinet
18 gauge type 304 stainless steel construction, with a stainless steel top, legs and undershelf
Overhang edge top that extends past the cabinet body at the ends, front and back
The Omcan 24407 Work Table
This Omcan cabinet base work table gives you a 60 inch stainless steel work surface with an enclosed cabinet underneath for storing kitchen equipment and other products. It is intended for food preparation in a busy commercial kitchen. Sliding doors close off the base, so what you keep under the work top stays behind doors. The top is 18-gauge type 304 stainless steel, and this is the overhang edge version, with the top larger than the cabinet body beneath it. A 4 inch by 1 inch backsplash runs along the back edge. The unit stands 38 inches high at the top of the backsplash on a 30 inch deep footprint, so measure your wall run and aisle clearance against the 60 inch width. The top is rated for 750 pounds and the undershelf inside the cabinet for 440 pounds. It arrives as a knock-down unit that assembles on site with set screws.
Enclosed Cabinet Base with Sliding Doors
The base is an enclosed cabinet closed in by a back panel and left and right side panels, with a stainless steel undershelf inside and two sliding doors across the front. The doors ride on slide rails and have recessed handles. The cabinet body measures 53-1/2 inches wide by 21-3/4 inches deep, and its bottom sits 12 inches off the floor.
18-Gauge Type 304 Stainless Steel Construction
Omcan builds this table in 18-gauge type 304 stainless steel. The top, the legs and the undershelf are all stainless steel, and the table is designed and finished for commercial use, so minor surface marks such as dimples, scratches and scuffs are normal on a product of this kind. The same table is available in type 430 stainless steel as item 24404.
4-Inch by 1-Inch Backsplash and Overhang Edge
The back edge carries a 4 inch by 1 inch backsplash. The work surface sits 34 inches off the floor and the top of the splash at 38 inches, worth checking if the table slides under a wall shelf. The rest of the top is the overhang edge: The top extends 3-1/4 inches beyond the cabinet body at each end and 4-1/8 inches at the front and back. The same table is available without a backsplash as item 24401.
Knock-Down Design Assembled on Site
The table arrives knocked down with four 34 inch stainless steel legs, the top, two sides, a back, the undershelf with its aluminum die cast clamp, two sliding doors and 36 set screws. The back and sides fasten to the top with set screws, the legs and undershelf assembly insert into gussets, and the doors are installed on the slide rails once the table is upright. The set screws should be filled with an approved silicone sealer, which is not included. The legs finish in stainless steel bullet feet. Optional 5 inch casters are items 47599 (without brake) and 14395 (with brake).
About Omcan
For over 74 years, Omcan has been a trusted name in the foodservice industry across Canada and the United States. Built on consistency, credibility, and long-standing customer relationships, Omcan offers a dependable range of products to support a wide range of operations. With a global network and localized service, the brand delivers complete solutions—from smallwares to advanced equipment. In 2024, Omcan introduced the Trento brand, representing a curated lineup of European foodservice equipment available exclusively in North America. Whether supporting independent operators or institutional kitchens, Omcan is focused on practical performance and reliable service.
Features & Benefits
-
Enclosed cabinet work table for food preparation in a busy commercial kitchen, with a 60 inch by 30 inch top
-
Cabinet is closed in by back and side panels with a stainless steel undershelf inside for storing kitchen equipment and other products
-
Two sliding doors on slide rails with recessed handles across the front of the cabinet
-
18 gauge type 304 stainless steel construction, with a stainless steel top, legs and undershelf
-
Overhang edge top that extends past the cabinet body at the ends, front and back
-
4 inch by 1 inch backsplash along the back of the top; the same table without a backsplash is item 24401
-
Top rated for a heavier load than the undershelf inside the cabinet
-
Four 34 inch stainless steel legs with stainless steel bullet feet; optional 5 inch casters available as items 47599 and 14395
-
Knock-down design that assembles on site with 36 set screws, which should be filled with an approved silicone sealer (not included)
Resources & Downloads
See all from Omcan
Specifications
| Top Size (D x W) | 30 x 60 in / 762 x 1524 mm |
| Overall Width | 60 in |
| Overall Depth | 30 in |
| Overall Height (to Top of Backsplash) | 38 in / 965.2 mm |
| Work Surface Height | 34 in |
| Backsplash | 4 x 1 in |
| Edge Style | Overhang |
| End Overhang | 3-1/4 in |
| Front and Back Overhang | 4-1/8 in |
| Cabinet Body Width | 53-1/2 in |
| Cabinet Body Depth | 21-3/4 in |
| Cabinet Floor Clearance | 12 in |
| Top Capacity | 750 lb / 340.2 kg |
| Undershelf Capacity | 440 lb / 199.6 kg |
| Material | 304 stainless steel |
| Gauge | 18 gauge |
| Base | Enclosed cabinet with undershelf |
| Doors | 2 sliding, recessed handles |
| Legs | 4 stainless steel, 34 in |
| Feet | Stainless steel bullet feet |
| Assembly | Knock-down, 36 set screws |
| Optional Casters | Items 47599 (no brake), 14395 (with brake) |
| 430 Stainless Steel Version | Item 24404 |
| Version Without Backsplash | Item 24401 |
Manufacturer's Warranty
-
6 Month
Warranty
Certifications & Approvals
-
NSF Approved
Enclosed cabinet work table for food preparation in a busy commercial kitchen, with a 60 inch by 30 inch top