The Omcan 28642 Work Table
This Omcan cabinet base work table gives you a 48 inch stainless steel work surface with an enclosed cabinet underneath for storing kitchen equipment and other products. Omcan lists it for food preparation in a busy commercial kitchen. Sliding doors close off the base, so what you keep under the work top stays behind doors. The top is 18-gauge type 430 stainless steel, and this is the flush edge version. A 4 inch by 1 inch backsplash runs along the back edge. The unit stands 38 inches high at the top of the backsplash on a 30 inch deep footprint, so measure your wall run and aisle clearance against the 48 inch width. It arrives as a knock-down unit that assembles on site with set screws.
Enclosed Cabinet Base with Sliding Doors
The base is an enclosed cabinet closed in by a back panel and left and right side panels, with a stainless steel undershelf inside and two sliding doors across the front. The doors ride on slide rails and have recessed handles. Omcan lists a replacement clip and bracket for the cabinet as item 69758.
18-Gauge Type 430 Stainless Steel Construction
Omcan builds this table in 18-gauge type 430 stainless steel. The top, the legs and the undershelf are all stainless steel, and the table is designed and finished for commercial use, so Omcan notes that minor surface marks such as dimples, scratches and scuffs are normal on a product of this kind.
4-Inch by 1-Inch Backsplash and Flush Edge
The back edge carries Omcan's 4 inch by 1 inch backsplash, which takes the overall height to 38 inches, worth checking if the table slides under a wall shelf. This is the flush edge version; Omcan lists the same table in an overhang edge version as item 24403 and the flush edge table without a backsplash as item 28639.
Knock-Down Design Assembled on Site
The table arrives knocked down with four 34 inch stainless steel legs, the top, two sides, a back, the undershelf with its aluminum die cast clamp, two sliding doors and 36 set screws. The back and sides fasten to the top with set screws, the legs and undershelf assembly insert into gussets, and the doors are installed on the slide rails once the table is upright. Omcan's manual calls for filling the set screws with an approved silicone sealer, which is not included. The legs finish in stainless steel bullet feet. Omcan lists a replacement foot as item AC015 and a 5 inch caster as item 14395 (with brake).
About Omcan
For over 74 years, Omcan has been a trusted name in the foodservice industry across Canada and the United States. Built on consistency, credibility, and long-standing customer relationships, Omcan offers a dependable range of products to support a wide range of operations. With a global network and localized service, the brand delivers complete solutions—from smallwares to advanced equipment. In 2024, Omcan introduced the Trento brand, representing a curated lineup of European foodservice equipment available exclusively in North America. Whether supporting independent operators or institutional kitchens, Omcan is focused on practical performance and reliable service.
Features & Benefits
-
Enclosed cabinet work table for food preparation in a busy commercial kitchen, with a 48 inch by 30 inch top
-
Cabinet is closed in by back and side panels with a stainless steel undershelf inside for storing kitchen equipment and other products
-
Two sliding doors on slide rails with recessed handles across the front of the cabinet
-
18 gauge type 430 stainless steel construction, with a stainless steel top, legs and undershelf
-
4 inch by 1 inch backsplash along the back of the top; Omcan lists the same table without a backsplash as item 28639
-
Flush edge version; Omcan also lists an overhang edge version of this size as item 24403
-
Four 34 inch stainless steel legs with stainless steel bullet feet; optional 5 inch caster with brake available as item 14395
-
Knock-down design that assembles on site with 36 set screws, which Omcan says to fill with an approved silicone sealer (not included)
-
Omcan lists a replacement foot (item AC015) and a replacement cabinet clip and bracket (item 69758) for this table
Free Shipping 48 Contiguous states & DC only.
In Stock: Ships in 1-2 Business Days
Enclosed cabinet work table for food preparation in a busy commercial kitchen, with a 48 inch by 30 inch top
Cabinet is closed in by back and side panels with a stainless steel undershelf inside for storing kitchen equipment and other products
Two sliding doors on slide rails with recessed handles across the front of the cabinet
18 gauge type 430 stainless steel construction, with a stainless steel top, legs and undershelf
4 inch by 1 inch backsplash along the back of the top; Omcan lists the same table without a backsplash as item 28639
The Omcan 28642 Work Table
This Omcan cabinet base work table gives you a 48 inch stainless steel work surface with an enclosed cabinet underneath for storing kitchen equipment and other products. Omcan lists it for food preparation in a busy commercial kitchen. Sliding doors close off the base, so what you keep under the work top stays behind doors. The top is 18-gauge type 430 stainless steel, and this is the flush edge version. A 4 inch by 1 inch backsplash runs along the back edge. The unit stands 38 inches high at the top of the backsplash on a 30 inch deep footprint, so measure your wall run and aisle clearance against the 48 inch width. It arrives as a knock-down unit that assembles on site with set screws.
Enclosed Cabinet Base with Sliding Doors
The base is an enclosed cabinet closed in by a back panel and left and right side panels, with a stainless steel undershelf inside and two sliding doors across the front. The doors ride on slide rails and have recessed handles. Omcan lists a replacement clip and bracket for the cabinet as item 69758.
18-Gauge Type 430 Stainless Steel Construction
Omcan builds this table in 18-gauge type 430 stainless steel. The top, the legs and the undershelf are all stainless steel, and the table is designed and finished for commercial use, so Omcan notes that minor surface marks such as dimples, scratches and scuffs are normal on a product of this kind.
4-Inch by 1-Inch Backsplash and Flush Edge
The back edge carries Omcan's 4 inch by 1 inch backsplash, which takes the overall height to 38 inches, worth checking if the table slides under a wall shelf. This is the flush edge version; Omcan lists the same table in an overhang edge version as item 24403 and the flush edge table without a backsplash as item 28639.
Knock-Down Design Assembled on Site
The table arrives knocked down with four 34 inch stainless steel legs, the top, two sides, a back, the undershelf with its aluminum die cast clamp, two sliding doors and 36 set screws. The back and sides fasten to the top with set screws, the legs and undershelf assembly insert into gussets, and the doors are installed on the slide rails once the table is upright. Omcan's manual calls for filling the set screws with an approved silicone sealer, which is not included. The legs finish in stainless steel bullet feet. Omcan lists a replacement foot as item AC015 and a 5 inch caster as item 14395 (with brake).
About Omcan
For over 74 years, Omcan has been a trusted name in the foodservice industry across Canada and the United States. Built on consistency, credibility, and long-standing customer relationships, Omcan offers a dependable range of products to support a wide range of operations. With a global network and localized service, the brand delivers complete solutions—from smallwares to advanced equipment. In 2024, Omcan introduced the Trento brand, representing a curated lineup of European foodservice equipment available exclusively in North America. Whether supporting independent operators or institutional kitchens, Omcan is focused on practical performance and reliable service.
Features & Benefits
-
Enclosed cabinet work table for food preparation in a busy commercial kitchen, with a 48 inch by 30 inch top
-
Cabinet is closed in by back and side panels with a stainless steel undershelf inside for storing kitchen equipment and other products
-
Two sliding doors on slide rails with recessed handles across the front of the cabinet
-
18 gauge type 430 stainless steel construction, with a stainless steel top, legs and undershelf
-
4 inch by 1 inch backsplash along the back of the top; Omcan lists the same table without a backsplash as item 28639
-
Flush edge version; Omcan also lists an overhang edge version of this size as item 24403
-
Four 34 inch stainless steel legs with stainless steel bullet feet; optional 5 inch caster with brake available as item 14395
-
Knock-down design that assembles on site with 36 set screws, which Omcan says to fill with an approved silicone sealer (not included)
-
Omcan lists a replacement foot (item AC015) and a replacement cabinet clip and bracket (item 69758) for this table
Resources & Downloads
See all from Omcan
Specifications
| Top Size (D x W) | 30 x 48 in / 762 x 1219.2 mm |
| Overall Width | 48 in |
| Overall Depth | 30 in |
| Overall Height (to Top of Backsplash) | 38 in / 965.2 mm |
| Work Surface Height | 34 in |
| Backsplash | 4 x 1 in |
| Edge Style | Flush |
| Material | 430 stainless steel |
| Gauge | 18 gauge |
| Base | Enclosed cabinet with undershelf |
| Doors | 2 sliding, recessed handles |
| Legs | 4 stainless steel, 34 in |
| Feet | Stainless steel bullet feet |
| Assembly | Knock-down, 36 set screws |
| Optional Caster | Item 14395 (with brake) |
| Replacement Foot | Item AC015 |
| Replacement Clip/Bracket | Item 69758 |
| Version Without Backsplash | Item 28639 |
| Overhang Edge Version | Item 24403 |
Manufacturer's Warranty
-
6 Month
Warranty
Certifications & Approvals
-
NSF Approved
Enclosed cabinet work table for food preparation in a busy commercial kitchen, with a 48 inch by 30 inch top