The Omcan 48890 Pineapple Cutter
This Omcan tabletop pineapple guillotine takes the top and tail off a pineapple in one swift motion, with minimal waste and effort, so the fruit is ready for peeling or slicing into pieces. It is a simple manual tool suited to pineapple cutting in large quantities and to both professional and domestic use, in hotels, restaurants, shops, supermarkets and greengrocers. It is entirely manual, so there is nothing to plug in, but give it working room: the base is 17 inches long, 12 inches wide and 7 inches tall, and the handle rises to about 16 inches when raised. The unit arrives ready to use, just set it on a flat, non-slip surface and make sure it is clean before the first case of fruit.
One Stroke Tops and Tails the Pineapple
Lay the pineapple horizontally in the cradle, lower the handle firmly, and two sharp blades cut the two ends of the fruit in a single motion, without much force and without the hand touching the cut. The result is a perfectly straight cut at each end, and the pineapple is ready for peeling or slicing into pieces.
Serrated Strips Hold the Fruit Secure
The serrated holding strips keep the pineapple secure as the blades come down, so the cut lands cleanly where you lined it up. A safety pin stays attached when the cutter is not in use, to keep the blades from falling accidentally; remove it before cutting and reinsert it when you are finished.
Bottom Gage Adjusts for Pineapple Size
The adjustable bottom gage sets the gap between the two blades for precision cuts, so the cutter handles different sizes of pineapple. Turn the adjustment levers and read the ruler on the product to set the blade width for the fruit you are using, up to a maximum gap of 18 cm (about 7.1 inches), and keep the blades parallel so the pineapple cuts properly.
Stainless Steel Body Built for Wet Fruit Work
Body and blade are food-grade stainless steel, which gives the structure durability and resistance to corrosion from acidic substances. The unit weighs 14 pounds and sits on non-slip feet. It cleans easily: rinse it under hot water or run it through the dishwasher with detergent, wipe the outer surface with a wet cloth, and avoid hard or abrasive materials. No routine maintenance is needed beyond daily cleaning.
About Omcan
For over 74 years, Omcan has been a trusted name in the foodservice industry across Canada and the United States. Built on consistency, credibility, and long-standing customer relationships, Omcan offers a dependable range of products to support a wide range of operations. With a global network and localized service, the brand delivers complete solutions—from smallwares to advanced equipment. In 2024, Omcan introduced the Trento brand, representing a curated lineup of European foodservice equipment available exclusively in North America. Whether supporting independent operators or institutional kitchens, Omcan is focused on practical performance and reliable service.
Features & Benefits
-
Guillotine cutter for hotels, restaurants, shops, supermarkets and greengrocers
-
One handle stroke takes the top and tail off together with a perfectly straight cut
-
Leaves the pineapple ready for peeling or slicing into pieces with minimal waste
-
Serrated holding strips keep the pineapple secure and the cut clean
-
Adjustable bottom gage sets the blade gap for different pineapple sizes, read against a ruler on the product
-
Simple manual tool suited to pineapple cutting in large quantities
-
Food-grade stainless steel body and blade resist corrosion from acidic juice
-
Non-slip feet on the base
-
Manual operation, no motor or outlet needed at the fruit station
-
Safety pin keeps the blades from falling when the cutter is not in use
Free Shipping 48 Contiguous states & DC only.
In Stock: Ships in 1-2 Business Days
Guillotine cutter for hotels, restaurants, shops, supermarkets and greengrocers
One handle stroke takes the top and tail off together with a perfectly straight cut
Leaves the pineapple ready for peeling or slicing into pieces with minimal waste
Serrated holding strips keep the pineapple secure and the cut clean
Adjustable bottom gage sets the blade gap for different pineapple sizes, read against a ruler on the product
The Omcan 48890 Pineapple Cutter
This Omcan tabletop pineapple guillotine takes the top and tail off a pineapple in one swift motion, with minimal waste and effort, so the fruit is ready for peeling or slicing into pieces. It is a simple manual tool suited to pineapple cutting in large quantities and to both professional and domestic use, in hotels, restaurants, shops, supermarkets and greengrocers. It is entirely manual, so there is nothing to plug in, but give it working room: the base is 17 inches long, 12 inches wide and 7 inches tall, and the handle rises to about 16 inches when raised. The unit arrives ready to use, just set it on a flat, non-slip surface and make sure it is clean before the first case of fruit.
One Stroke Tops and Tails the Pineapple
Lay the pineapple horizontally in the cradle, lower the handle firmly, and two sharp blades cut the two ends of the fruit in a single motion, without much force and without the hand touching the cut. The result is a perfectly straight cut at each end, and the pineapple is ready for peeling or slicing into pieces.
Serrated Strips Hold the Fruit Secure
The serrated holding strips keep the pineapple secure as the blades come down, so the cut lands cleanly where you lined it up. A safety pin stays attached when the cutter is not in use, to keep the blades from falling accidentally; remove it before cutting and reinsert it when you are finished.
Bottom Gage Adjusts for Pineapple Size
The adjustable bottom gage sets the gap between the two blades for precision cuts, so the cutter handles different sizes of pineapple. Turn the adjustment levers and read the ruler on the product to set the blade width for the fruit you are using, up to a maximum gap of 18 cm (about 7.1 inches), and keep the blades parallel so the pineapple cuts properly.
Stainless Steel Body Built for Wet Fruit Work
Body and blade are food-grade stainless steel, which gives the structure durability and resistance to corrosion from acidic substances. The unit weighs 14 pounds and sits on non-slip feet. It cleans easily: rinse it under hot water or run it through the dishwasher with detergent, wipe the outer surface with a wet cloth, and avoid hard or abrasive materials. No routine maintenance is needed beyond daily cleaning.
About Omcan
For over 74 years, Omcan has been a trusted name in the foodservice industry across Canada and the United States. Built on consistency, credibility, and long-standing customer relationships, Omcan offers a dependable range of products to support a wide range of operations. With a global network and localized service, the brand delivers complete solutions—from smallwares to advanced equipment. In 2024, Omcan introduced the Trento brand, representing a curated lineup of European foodservice equipment available exclusively in North America. Whether supporting independent operators or institutional kitchens, Omcan is focused on practical performance and reliable service.
Features & Benefits
-
Guillotine cutter for hotels, restaurants, shops, supermarkets and greengrocers
-
One handle stroke takes the top and tail off together with a perfectly straight cut
-
Leaves the pineapple ready for peeling or slicing into pieces with minimal waste
-
Serrated holding strips keep the pineapple secure and the cut clean
-
Adjustable bottom gage sets the blade gap for different pineapple sizes, read against a ruler on the product
-
Simple manual tool suited to pineapple cutting in large quantities
-
Food-grade stainless steel body and blade resist corrosion from acidic juice
-
Non-slip feet on the base
-
Manual operation, no motor or outlet needed at the fruit station
-
Safety pin keeps the blades from falling when the cutter is not in use
Resources & Downloads
See all from Omcan
Specifications
| Operation | Manual guillotine |
| Mounting | Tabletop |
| Material | Food-grade stainless steel |
| Blades | 2, stainless steel |
| Cut Style | Straight, top and tail in one motion |
| Holding Strips | Serrated |
| Cut Adjustment | Bottom gage with adjustment levers and ruler |
| Maximum Blade Gap | 18 cm (7.1 in) |
| Feet | Non-slip |
| Power Required | None |
| Suitable Use | Professional and domestic |
| Overall Width | 17 in (432 mm) |
| Overall Depth | 12 in (305 mm) |
| Overall Height | 7 in (178 mm) |
| Height with Handle Raised | 16 in (406 mm) |
| Net Weight | 14 lb (6.4 kg) |
| Country of Origin | Turkey |
Manufacturer's Warranty
-
1 Month
Warranty
Guillotine cutter for hotels, restaurants, shops, supermarkets and greengrocers